Re: [PATCH net-next v3 02/13] phy: add the mvebu cp110 comphy driver
From: Antoine Tenart
Date: Tue Aug 29 2017 - 09:12:38 EST
Hi Kishon,
On Tue, Aug 29, 2017 at 05:55:06PM +0530, Kishon Vijay Abraham I wrote:
> On Tuesday 29 August 2017 04:53 PM, Antoine Tenart wrote:
> > On Tue, Aug 29, 2017 at 04:34:17PM +0530, Kishon Vijay Abraham I wrote:
> >> On Monday 28 August 2017 08:27 PM, Antoine Tenart wrote:
> >>> +static const struct mvebu_comhy_conf mvebu_comphy_cp110_modes[] = {
> >>> + /* lane 0 */
> >>> + MVEBU_COMPHY_CONF(0, 1, PHY_MODE_SGMII, 0x1),
> >>> + /* lane 1 */
> >>> + MVEBU_COMPHY_CONF(1, 2, PHY_MODE_SGMII, 0x1),
> >>> + /* lane 2 */
> >>> + MVEBU_COMPHY_CONF(2, 0, PHY_MODE_SGMII, 0x1),
> >>> + MVEBU_COMPHY_CONF(2, 0, PHY_MODE_10GKR, 0x1),
> >>> + /* lane 3 */
> >>> + MVEBU_COMPHY_CONF(3, 1, PHY_MODE_SGMII, 0x2),
> >>> + /* lane 4 */
> >>> + MVEBU_COMPHY_CONF(4, 0, PHY_MODE_SGMII, 0x2),
> >>> + MVEBU_COMPHY_CONF(4, 0, PHY_MODE_10GKR, 0x2),
> >>> + MVEBU_COMPHY_CONF(4, 1, PHY_MODE_SGMII, 0x1),
> >>> + /* lane 5 */
> >>> + MVEBU_COMPHY_CONF(5, 2, PHY_MODE_SGMII, 0x1),
> >>> +};
> >>
> >> IMHO all the lane and mode configuration should come from dt. That would make
> >> it more reusable when comphy is configured differently.
> >
> > These connexions between engines and the comphy lanes are inside the
> > SoC. They won't change for a given SoC, and the actual configuration is
> > at the board level to know what is connected to the output of a given
> > lane, which is already described into the dt (the lane phandle).
> >
> > So I think we can keep this inside the driver, and we'll had other
> > tables if the same comphy is ever used in another SoC.
> >
> > What do you think?
>
> I'd like to avoid adding tables for every SoC. These are configuration details
> and can come from dt.
Actually this is per CP design, not SoC (this one is used in both 7k and
8k SoCs from Marvell, and probably others). I'm still not convinced this
is a good idea to put this into the dt. First of all we would end up with
something like (and this is only for a single lane, out of *6*):
cpm_comphy: phy@phy@120000 {
compatible = "marvell,comphy-cp110";
reg = <0x120000 0x6000>;
marvell,system-controller = <&cpm_syscon0>;
#address-cells = <1>;
#size-cells = <0>;
cpm_comphy0: phy@0 {
reg = <0>;
#phy-cells = <1>;
mode@0 {
phy-mode = PHY_MODE_SGMII;
selector = <0x1>;
pipe-selector = <0x0>;
port = <0>;
};
mode@1 {
phy-mode = PHY_MODE_HS_SGMII;
selector = <0x1>;
pipe-selector = <0x0>;
port = <0>;
};
mode@2 {
phy-mode = PHY_MODE_RXAUI;
selector = <0x2>;
pipe-selector = <0x0>;
port = <0>;
};
mode@3 {
phy-mode = PHY_MODE_10GKR;
selector = <0x2>;
pipe-selector = <0x0>;
port = <0>;
};
mode@4 {
phy-mode = PHY_MODE_SATA;
selector = <0x4>;
pipe-selector = <0x0>;
port = <1>;
};
mode@5 {
phy-mode = PHY_MODE_USB;
selector = <0x0>;
pipe-selector = <0x1>;
port = <2>;
};
mode@6 {
phy-mode = PHY_MODE_USB;
selector = <0x0>;
pipe-selector = <0x2>;
port = <0>;
};
... + PCIe, other ports ...
};
cpm_comphy1: phy@1 {
...
};
...
};
And this "configuration" makes us think the comphy driver would be
somehow generic with only these parameters to update when using a
different CP. In reality we do have one other comphy in another CP, and
it requires more than just updating the above parameters: the init
functions also are SoC specific. So the table used in the patch proposed
only is a small part of this "configuration". In fact it's not a
configuration at all, but only a mode-to-bit indirection, used in the
comphy init functions.
What is proposed instead, is very close to what actually changes a lot,
and what a designer can change: the CP internals are described in the
driver as these won't change (and if they do in a future CP design, a
lot more effort would be needed than just updating the table), and the
actual lane connexions on the board are configured through the dt, which
is board specific.
Finally we do not have (yet) any example of this IP being reused as-is.
So we have no idea what other changes than the ones described above will
be needed. But for sure not only the mode and lane configurations.
Thanks,
Antoine
--
Antoine Ténart, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
Attachment:
signature.asc
Description: PGP signature