Re: [PATCH v2 1/1] usb:xhci: update condition to select bus->sysdev from parent device

[Mathias Nyman]

On 24.08.2017 05:53, Thang Q. Nguyen wrote:
> On Sat, Aug 19, 2017 at 10:43 AM, Thang Q. Nguyen <tqnguyen@xxxxxxx> wrote:
> > From: "Thang Q. Nguyen" <tqnguyen@xxxxxxx>
> >
> > For commit 4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA
> > configuration"), sysdev points to devices known to the system firmware
> > or hardware for DMA parameters.
> > However, the parent of the system firmware/hardware device checking
> > logic does not work in ACPI boot mode. This patch updates the formulation
> > to check this case in both DT and ACPI.
> >
> > Signed-off-by: Tung Nguyen <tunguyen@xxxxxxx>
> > Signed-off-by: Thang Q. Nguyen <tqnguyen@xxxxxxx>
> > ---
> > Change since v1:
> >   - Update codes to work with kernel 4.13-rc5
> > ---
> >   drivers/usb/host/xhci-plat.c | 5 ++++-
> >   1 file changed, 4 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
> > index c04144b..1bb9729 100644
> > --- a/drivers/usb/host/xhci-plat.c
> > +++ b/drivers/usb/host/xhci-plat.c
> > @@ -187,7 +187,10 @@ static int xhci_plat_probe(struct platform_device *pdev)
> >           * 3. xhci_plat is grandchild of a pci device (dwc3-pci)
> >           */
> >          sysdev = &pdev->dev;
> > -       if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
> > +       if (sysdev->parent && !is_of_node(sysdev->fwnode) &&
> > +                       !is_acpi_device_node(sysdev->fwnode) &&
> > +                       (is_of_node(sysdev->parent->fwnode) ||
> > +                        is_acpi_device_node(sysdev->parent->fwnode)))
> >                  sysdev = sysdev->parent;
> >   #ifdef CONFIG_PCI
> >          else if (sysdev->parent && sysdev->parent->parent &&
> > --
> > 1.8.3.1
> Is there any comment about the patch?
> With current kernel (4.13.0-rc6), booting the Linux using ACPI boot,
> kernel is crashed right after probing the USB DWC3 driver with the
> following messages:

That should work, but the if statements are getting quite elaborate.
How about replacing it all with:

-       sysdev = &pdev->dev;
-       if (sysdev->parent && !sysdev->of_node && sysdev->parent->of_node)
-               sysdev = sysdev->parent;
-#ifdef CONFIG_PCI
-       else if (sysdev->parent && sysdev->parent->parent &&
-                sysdev->parent->parent->bus == &pci_bus_type)
-               sysdev = sysdev->parent->parent;
-#endif
+
+       for (sysdev = &pdev->dev; sysdev; sysdev = sysdev->parent) {
+               if (is_of_node(sysdev->fwnode) ||
+                   is_acpi_device_node(sysdev->fwnode))
+                       break;
+       #ifdef CONFIG_PCI
+               else if (sysdev->bus == &pci_bus_type)
+                       break;
+       #endif
+       }
+
+       if (!sysdev)
+               sysdev = &pdev->dev

Does that work for you?

-Mathias