Re: [PATCH v2 05/18] firmware: arm_scmi: add initial support for performance protocol
From: Julien Thierry
Date: Tue Sep 05 2017 - 11:05:01 EST
Hi Sudeep,
On 04/08/17 15:31, Sudeep Holla wrote:
The performance protocol is intended for the performance management of
group(s) of device(s) that run in the same performance domain. It
includes even the CPUs. A performance domain is defined by a set of
devices that always have to run at the same performance level.
For example, a set of CPUs that share a voltage domain, and have a
common frequency control, is said to be in the same performance domain.
The commands in this protocol provide functionality to describe the
protocol version, describe various attribute flags, set and get the
performance level of a domain. It also supports discovery of the list
of performance levels supported by a performance domain, and the
properties of each performance level.
This patch adds basic support for the performance protocol.
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Signed-off-by: Sudeep Holla <sudeep.holla@xxxxxxx>
---
drivers/firmware/arm_scmi/Makefile | 2 +-
drivers/firmware/arm_scmi/common.h | 1 +
drivers/firmware/arm_scmi/perf.c | 511 +++++++++++++++++++++++++++++++++++++
include/linux/scmi_protocol.h | 31 +++
4 files changed, 544 insertions(+), 1 deletion(-)
create mode 100644 drivers/firmware/arm_scmi/perf.c
diff --git a/drivers/firmware/arm_scmi/Makefile b/drivers/firmware/arm_scmi/Makefile
index 21d01d1d6b9c..159de726ee45 100644
--- a/drivers/firmware/arm_scmi/Makefile
+++ b/drivers/firmware/arm_scmi/Makefile
@@ -1,2 +1,2 @@
obj-$(CONFIG_ARM_SCMI_PROTOCOL) = arm_scmi.o
-arm_scmi-y = base.o driver.o
+arm_scmi-y = base.o driver.o perf.o
diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index e3fe5d9acc82..7473dfcad4ee 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -30,6 +30,7 @@
#define PROTOCOL_REV_MAJOR(x) ((x) >> PROTOCOL_REV_MINOR_BITS)
#define PROTOCOL_REV_MINOR(x) ((x) & PROTOCOL_REV_MINOR_MASK)
#define MAX_PROTOCOLS_IMP 16
+#define MAX_OPPS 16
enum scmi_std_protocol {
SCMI_PROTOCOL_BASE = 0x10,
diff --git a/drivers/firmware/arm_scmi/perf.c b/drivers/firmware/arm_scmi/perf.c
new file mode 100644
index 000000000000..13d84d829201
--- /dev/null
+++ b/drivers/firmware/arm_scmi/perf.c
@@ -0,0 +1,511 @@
+/*
+ * System Control and Management Interface (SCMI) Performance Protocol
+ *
+ * Copyright (C) 2017 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/sort.h>
+
+#include "common.h"
+
+enum scmi_performance_protocol_cmd {
+ PERF_DOMAIN_ATTRIBUTES = 0x3,
+ PERF_DESCRIBE_LEVELS = 0x4,
+ PERF_LIMITS_SET = 0x5,
+ PERF_LIMITS_GET = 0x6,
+ PERF_LEVEL_SET = 0x7,
+ PERF_LEVEL_GET = 0x8,
+ PERF_NOTIFY_LIMITS = 0x9,
+ PERF_NOTIFY_LEVEL = 0xa,
+};
+
+struct scmi_opp {
+ u32 perf;
+ u32 power;
+ u32 trans_latency_us;
+};
+
+struct scmi_msg_resp_perf_attributes {
+ __le16 num_domains;
+ __le16 flags;
+#define POWER_SCALE_IN_MILLIWATT(x) ((x) & BIT(0))
+ __le32 stats_addr_low;
+ __le32 stats_addr_high;
+ __le32 stats_size;
+};
+
+struct scmi_msg_resp_perf_domain_attributes {
+ __le32 flags;
+#define SUPPORTS_SET_LIMITS(x) ((x) & BIT(31))
+#define SUPPORTS_SET_PERF_LVL(x) ((x) & BIT(30))
+#define SUPPORTS_PERF_LIMIT_NOTIFY(x) ((x) & BIT(29))
+#define SUPPORTS_PERF_LEVEL_NOTIFY(x) ((x) & BIT(28))
+ __le32 rate_limit_us;
+ __le32 sustained_freq_khz;
+ __le32 sustained_perf_level;
+ u8 name[SCMI_MAX_STR_SIZE];
+};
+
+struct scmi_msg_perf_describe_levels {
+ __le32 domain;
+ __le32 level_index;
+};
+
+struct scmi_perf_set_limits {
+ __le32 domain;
+ __le32 max_level;
+ __le32 min_level;
+};
+
+struct scmi_perf_get_limits {
+ __le32 max_level;
+ __le32 min_level;
+};
+
+struct scmi_perf_set_level {
+ __le32 domain;
+ __le32 level;
+};
+
+struct scmi_perf_notify_level_or_limits {
+ __le32 domain;
+ __le32 notify_enable;
+};
+
+struct scmi_msg_resp_perf_describe_levels {
+ __le16 num_returned;
+ __le16 num_remaining;
+ struct {
+ __le32 perf_val;
+ __le32 power;
+ __le16 transition_latency_us;
+ __le16 reserved;
+ } opp[0];
+};
+
+struct perf_dom_info {
+ bool set_limits;
+ bool set_perf;
+ bool perf_limit_notify;
+ bool perf_level_notify;
+ u32 opp_count;
+ u32 sustained_freq_khz;
+ u32 sustained_perf_level;
+ u32 mult_factor;
+ char name[SCMI_MAX_STR_SIZE];
+ struct scmi_opp opp[MAX_OPPS];
+};
+
+struct scmi_perf_info {
+ int num_domains;
+ bool power_scale_mw;
+ u64 stats_addr;
+ u32 stats_size;
+ struct perf_dom_info *dom_info;
+};
+
+static struct scmi_perf_info perf_info;
+
+static int scmi_perf_attributes_get(const struct scmi_handle *handle,
+ struct scmi_perf_info *perf_info)
+{
+ int ret;
+ struct scmi_xfer *t;
+ struct scmi_msg_resp_perf_attributes *attr;
+
+ ret = scmi_one_xfer_init(handle, PROTOCOL_ATTRIBUTES,
+ SCMI_PROTOCOL_PERF, 0, sizeof(*attr), &t);
+ if (ret)
+ return ret;
+
+ attr = t->rx.buf;
+
+ ret = scmi_do_xfer(handle, t);
+ if (!ret) {
+ u16 flags = le16_to_cpu(attr->flags);
+
+ perf_info->num_domains = le16_to_cpu(attr->num_domains);
+ perf_info->power_scale_mw = POWER_SCALE_IN_MILLIWATT(flags);
+ perf_info->stats_addr = le32_to_cpu(attr->stats_addr_low) |
+ (u64)le32_to_cpu(attr->stats_addr_high) << 32;
This seems odd, shouldn't it be the following?
le64_to_cpu(attr->stats_addr_low | (__le64)attr->stats_addr_high << 32)
Cheers,
--
Julien Thierry