[patch 17/52] x86/apic: Move probe32 specific APIC functions

[Thomas Gleixner]

The apic functions which are used in probe_32.c are implemented as inlines
or in apic.c. There is no reason to have them at random places.

Move them to the actual usage site and make them static.

Signed-off-by: Thomas Gleixner <tglx@xxxxxxxxxxxxx>
---
 arch/x86/include/asm/apic.h     |   21 ---------------------
 arch/x86/kernel/apic/apic.c     |   10 ----------
 arch/x86/kernel/apic/probe_32.c |   25 +++++++++++++++++++++++++
 3 files changed, 25 insertions(+), 31 deletions(-)

--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -515,31 +515,10 @@ extern void default_setup_apic_routing(v
 extern struct apic apic_noop;
 
 #ifdef CONFIG_X86_32
-
 static inline int noop_x86_32_early_logical_apicid(int cpu)
 {
 	return BAD_APICID;
 }
-
-/*
- * Set up the logical destination ID.
- *
- * Intel recommends to set DFR, LDR and TPR before enabling
- * an APIC.  See e.g. "AP-388 82489DX User's Manual" (Intel
- * document number 292116).  So here it goes...
- */
-extern void default_init_apic_ldr(void);
-
-static inline int default_apic_id_registered(void)
-{
-	return physid_isset(read_apic_id(), phys_cpu_present_map);
-}
-
-static inline int default_phys_pkg_id(int cpuid_apic, int index_msb)
-{
-	return cpuid_apic >> index_msb;
-}
-
 #endif
 
 extern int flat_cpu_mask_to_apicid(const struct cpumask *cpumask,
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -2231,16 +2231,6 @@ int hard_smp_processor_id(void)
 	return read_apic_id();
 }
 
-void default_init_apic_ldr(void)
-{
-	unsigned long val;
-
-	apic_write(APIC_DFR, APIC_DFR_VALUE);
-	val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
-	val |= SET_APIC_LOGICAL_ID(1UL << smp_processor_id());
-	apic_write(APIC_LDR, val);
-}
-
 int default_cpu_mask_to_apicid(const struct cpumask *mask,
 			       struct irq_data *irqdata,
 			       unsigned int *apicid)
--- a/arch/x86/kernel/apic/probe_32.c
+++ b/arch/x86/kernel/apic/probe_32.c
@@ -66,6 +66,31 @@ static void setup_apic_flat_routing(void
 #endif
 }
 
+static int default_apic_id_registered(void)
+{
+	return physid_isset(read_apic_id(), phys_cpu_present_map);
+}
+
+/*
+ * Set up the logical destination ID.  Intel recommends to set DFR, LDR and
+ * TPR before enabling an APIC.  See e.g. "AP-388 82489DX User's Manual"
+ * (Intel document number 292116).
+ */
+static void default_init_apic_ldr(void)
+{
+	unsigned long val;
+
+	apic_write(APIC_DFR, APIC_DFR_VALUE);
+	val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
+	val |= SET_APIC_LOGICAL_ID(1UL << smp_processor_id());
+	apic_write(APIC_LDR, val);
+}
+
+static int default_phys_pkg_id(int cpuid_apic, int index_msb)
+{
+	return cpuid_apic >> index_msb;
+}
+
 /* should be called last. */
 static int probe_default(void)
 {