[PATCH v3 3/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry

From: Icenowy Zheng
Date: Fri Oct 06 2017 - 02:43:42 EST

The Banana Pi M2 Ultra is an SBC based on the Allwinner V40 SoC (same as
the R40 SoC). The form factor is similar to the Raspberry Pi series.

It features:

- X-Powers AXP221s PMIC connected to i2c0
- 1GiB DDR3 DRAM
- microSD slot
- MicroUSB Type-B port for power and connected to usb0
- HDMI output
- MIPI DSI connector
- 4 USB Type-A ports (connected to the usb1 controller via a hub)
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 module, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- audio out headphone jack
- red and green LEDs
- debug UART pins
- Raspberry Pi B+ compatible GPIO header
- power and reset buttons

This patch adds a dts file that enables UART, MMC and PMIC support.

Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
---
Changes in v2:
- Dropped the vcc5v0 regulator, as it's not used yet.

arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 164 ++++++++++++++++++++++
2 files changed, 166 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 93b1e63a52af..da3f87b35059 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -941,7 +941,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-r16-parrot.dtb \
sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v3s-licheepi-zero.dtb \
- sun8i-v3s-licheepi-zero-dock.dtb
+ sun8i-v3s-licheepi-zero-dock.dtb \
+ sun8i-v40-bananapi-m2-berry.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
new file mode 100644
index 000000000000..8a69be2a0842
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@xxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-r40.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Banana Pi M2 Berry";
+ compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ label = "bananapi:red:pwr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ user-led {
+ label = "bananapi:green:user";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+&reg_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <&reg_dldo2>;
+ vqmmc-supply = <&reg_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.13.6