Re: [PATCH 3/3] ARM: dts: gr-peach: Add ETHER pin group

[jacopo mondi]

Hi Simon,

On Thu, Oct 05, 2017 at 10:58:20AM +0200, Jacopo Mondi wrote:
> Add pin configuration subnode for ETHER pin group and enable the interface.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> ---
>  arch/arm/boot/dts/r7s72100-gr-peach.dts | 38 +++++++++++++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>

Can you confirm you have not applied this yet?

I have received indications from netdev people to change location of
the reset pin properties, as they belong to PHY node, and also to
change the node layout.

If you have applied the first 2 but not this one, I will re-submit this one only

Thanks
   j


> diff --git a/arch/arm/boot/dts/r7s72100-gr-peach.dts b/arch/arm/boot/dts/r7s72100-gr-peach.dts
> index ad6a627..8b5a2c5 100644
> --- a/arch/arm/boot/dts/r7s72100-gr-peach.dts
> +++ b/arch/arm/boot/dts/r7s72100-gr-peach.dts
> @@ -68,6 +68,28 @@
>  		/* P6_2 as RxD2; P6_3 as TxD2 */
>  		pinmux = <RZA1_PINMUX(6, 2, 7)>, <RZA1_PINMUX(6, 3, 7)>;
>  	};
> +
> +	ether_pins: ether {
> +		/* Ethernet on Ports 1,3,5,10 */
> +		pinmux = <RZA1_PINMUX(1, 14, 4)>, /* P1_14 = ET_COL   */
> +			 <RZA1_PINMUX(3, 0, 2)>,  /* P3_0 = ET_TXCLK  */
> +			 <RZA1_PINMUX(3, 3, 2)>,  /* P3_3 = ET_MDIO   */
> +			 <RZA1_PINMUX(3, 4, 2)>,  /* P3_4 = ET_RXCLK  */
> +			 <RZA1_PINMUX(3, 5, 2)>,  /* P3_5 = ET_RXER   */
> +			 <RZA1_PINMUX(3, 6, 2)>,  /* P3_6 = ET_RXDV   */
> +			 <RZA1_PINMUX(5, 9, 2)>,  /* P5_9 = ET_MDC    */
> +			 <RZA1_PINMUX(10, 1, 4)>, /* P10_1 = ET_TXER  */
> +			 <RZA1_PINMUX(10, 2, 4)>, /* P10_2 = ET_TXEN  */
> +			 <RZA1_PINMUX(10, 3, 4)>, /* P10_3 = ET_CRS   */
> +			 <RZA1_PINMUX(10, 4, 4)>, /* P10_4 = ET_TXD0  */
> +			 <RZA1_PINMUX(10, 5, 4)>, /* P10_5 = ET_TXD1  */
> +			 <RZA1_PINMUX(10, 6, 4)>, /* P10_6 = ET_TXD2  */
> +			 <RZA1_PINMUX(10, 7, 4)>, /* P10_7 = ET_TXD3  */
> +			 <RZA1_PINMUX(10, 8, 4)>, /* P10_8 = ET_RXD0  */
> +			 <RZA1_PINMUX(10, 9, 4)>, /* P10_9 = ET_RXD1  */
> +			 <RZA1_PINMUX(10, 10, 4)>,/* P10_10 = ET_RXD2 */
> +			 <RZA1_PINMUX(10, 11, 4)>;/* P10_11 = ET_RXD3 */
> +	};
>  };
>
>  &extal_clk {
> @@ -88,3 +110,19 @@
>
>  	status = "okay";
>  };
> +
> +&ether {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ether_pins>;
> +
> +	status = "okay";
> +
> +	reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;
> +	reset-delay-us = <5>;
> +
> +	renesas,no-ether-link;
> +	phy-handle = <&phy0>;
> +	phy0: ethernet-phy@0 {
> +		reg = <0>;
> +	};
> +};
> --
> 2.7.4
>