Re: [PATCH] firmware: bluefield: add boot control driver

[Sudeep Holla]

(+Mark, Grant)

On 09/10/17 18:16, Chris Metcalf wrote:
> The Mellanox BlueField SoC firmware supports a safe upgrade mode as
> part of the flow where users put new firmware on the secondary eMMC
> boot partition (the one not currently in use), tell the eMMC to make
> the secondary boot partition primary, and reset.  This driver is
> used to request that the firmware start the ARM watchdog after the
> next reset, and also request that the firmware swap the eMMC boot
> partition back again on the reset after that (the second reset).
> This means that if anything goes wrong, the watchdog will fire, the
> system will reset, and the firmware will switch back to the original
> boot partition.  If the boot is successful, the user will use this
> driver to put the firmware back into the state where it doesn't touch
> the eMMC boot partition at reset, and turn off the ARM watchdog.
> 
> The firmware allows for more configurability than that, as can
> be seen in the code, but the use case above is what the driver
> primarily supports.
> 
> It is structured as a simple sysfs driver that is loaded based on
> an ACPI table entry, and allows reading/writing text strings to
> various /sys/bus/platform/drivers/mlx-bootctl/* files.
> 
> Signed-off-by: Chris Metcalf <cmetcalf@xxxxxxxxxxxx>
> ---
> Ingo, since there isn't an overall maintainer for drivers/firmware,
> does it make sense for this to go through your tree?  Thanks!
> 
>  drivers/firmware/Kconfig       |  12 +++
>  drivers/firmware/Makefile      |   1 +
>  drivers/firmware/mlx-bootctl.c | 222 +++++++++++++++++++++++++++++++++++++++++
>  drivers/firmware/mlx-bootctl.h | 103 +++++++++++++++++++
>  4 files changed, 338 insertions(+)
>  create mode 100644 drivers/firmware/mlx-bootctl.c
>  create mode 100644 drivers/firmware/mlx-bootctl.h
> 
> diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
> index 6e4ed5a9c6fd..1f2adbcc5acc 100644
> --- a/drivers/firmware/Kconfig
> +++ b/drivers/firmware/Kconfig
> @@ -230,6 +230,18 @@ config TI_SCI_PROTOCOL
>  	  This protocol library is used by client drivers to use the features
>  	  provided by the system controller.
>  
> +config MLX_BOOTCTL
> +	tristate "Mellanox BlueField Firmware Boot Control"
> +	depends on ARM64
> +	help
> +	  The Mellanox BlueField firmware implements functionality to
> +	  request swapping the primary and alternate eMMC boot
> +	  partition, and to set up a watchdog that can undo that swap
> +	  if the system does not boot up correctly.  This driver
> +	  provides sysfs access to the firmware, to be used in
> +	  conjunction with the eMMC device driver to do any necessary
> +	  initial swap of the boot partition.
> +
For me, this looks like any other distro upgrade use-case which requires
to set some variable that must persist across reset (i.e. in non
volatile memory)

ARM is proposing Embedded Base Boot Requirements (EBBR)[1] and it covers
this IIUC. I am not sure if we need to achieve that using SMCCC as
proposed in the patch. I may be wrong, but just wanted to check.

-- 
[1]
https://developer.arm.com/products/architecture/system-architecture/embedded-system-architecture
-- 
Regards,
Sudeep