Re: [PATCH 3/5] dmaengine: Support for querying maximum trasnfer length (of an SG element)

[Peter Ujfalusi]

ï
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

On 10/08/2017 08:25 AM, Vinod Koul wrote:
>>>> It is not really static, the size in bytes depends on the dev_width and
>>>> the maxburst:
>>>> dev_width * burst * (SZ_64K - 1);
>>>
>>> well DMAengines work on FIFOs, in above you are giving length as SZ_64K - 1
>>> 'items' which IIUC in DMAengine terms for bytes would always refer wrt width
>>> used and burst applied.
>>
>> I think we can live with this and let the user to figure out what to do
>> with this information.
> 
> Right, plus a macro for conversion :) SO that users dont code buggy
> conversions all over the place

OK, but still the naming... ;)

>> But I'm having hard time to figure out a good name for this. It is not
>> the number of SGs we can support, but the number of 'items' within one
>> SG that we have the limit. It could be:
>> u32 max_bursts_per_sg;
> 
> this looks fine, another candidate I would use is words_per_sg and while at
> it why tie it to sg? should we make it words_per_txn but then people should not
> confuse with txn represented by a descriptor which can have multiple ....

Yes, this limit is not only per SG as the same limit actually applies to
cyclic's period_len in a same way.

words_per_txn does not sound right as for me the words would refer to
dev_width number of bytes and I'm seeking on limit on the number of (dev_width
* bursts) sub-chunks.

bursts_per_chunk? With a long comment?

Which would apply to sg_dma_len in slave_sg(), period_len in cyclic() and len
in slave_single().

>>
>> which would also apply to period length (for cyclic) in a similar way.
>>
>>> Return length in bytes does make sense (from user PoV), but then you need to
>>> "know" the applied  width and burst. How do you decide those?
>>
>> The number of items works eDMA and sDMA, but we also have the cpp41. It
>> is a packet DMA and it has no understanding of bursts, address widths or
>> any of the 'traditional' things. It only cares about the number of bytes
>> we want to transfer and it has limitation of 4194303 bytes (21bits for
>> length). This is again per SG. How this could report the
>> 'max_bursts_per_sg' ?
> 
> hmmm that is intresting case, is this number coming from USB side?

No, it is coming from cppi4.1's descriptor. The maximum length of a packet is
stored in 21bits.

But this is a bit more complicated ;) The whole packet have 21bits size limit,
but at the same time the whole sg_dma_len() also have this as we can link a
several host buffer descriptors to one host packet descriptor. Each have
21bits for length, but at the same time the sum of the hpd and the linked hbd
length can not be more than what we can store in 21bits...

> 
>> This was one of the reasons that I have settled with the callback.
>>
>> What we can also do is to code this within the DMA drivers itself.
>>
>> When setting up the transfer and we realize that one of the SG will not
>> going to fit, we destroy what we have done so far, pass the sg list
>> along with length/sg limit to create a new sg list where all sg item's
>> length is under the limit. Then using this new sg list we can set up the
>> transfer.
>>
>> I'm not sure how hard is to do the sg list optimization, I see that
>> sg_split() is not what we want so we might need to code this in
>> dmaengine or in the scatterlist code.
>>
>> We certainly don't want to verify all slave_sg transfers proactively to
>> avoid adding latency when it is not necessary.
> 
> latency would be added at prepare, not when submitting..

Yes, but you submit transfers all the time, and added latency would be crucial.

But this could be done with a DMAengine internal helper, I think.
If a DMA driver figures out that one of the SG length is over the supported
limit, then it could clean up everything and call something like:

struct dma_async_tx_descriptor *dmaengine_fixup_and_prep_slave_sg(
	struct dma_chan *chan, struct scatterlist *sgl,
	unsigned int sg_len, enum dma_transfer_direction dir,
	unsigned long flags, size_t max_sg_dma_len)

and this would split up the original SG list to a temp one meeting the
max_sg_dma_len and call chan->device->device_prep_slave_sg()

In this round the setup would succeed and the caller and I would be happy.

But if the caller already aware of the sg_dma_len limit it can prepare the SG
list correctly and we save time to recreate the list.

-- 
PÃter