Re: [PATCH v3 2/3] usb: xhci: Add DbC support in xHCI driver

[Greg Kroah-Hartman]

On Thu, Nov 02, 2017 at 09:36:42AM +0800, Lu Baolu wrote:
> Hi Greg,
> 
> On 09/05/2017 09:58 AM, Lu Baolu wrote:
> > xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
> > can be implemented with the Debug Capability(DbC). It presents a debug
> > device which is fully compliant with the USB framework and provides the
> > equivalent of a very high performance full-duplex serial link. The debug
> > capability operation model and registers interface are defined in 7.6.8
> > of the xHCI specification, revision 1.1.
> >
> > The DbC debug device shares a root port with the xHCI host. By default,
> > the debug capability is disabled and the root port is assigned to xHCI.
> > When the DbC is enabled, the root port will be assigned to the DbC debug
> > device, and the xHCI sees nothing on this port. This implementation uses
> > a sysfs node named <dbc> under the xHCI device to manage the enabling
> > and disabling of the debug capability.
> >
> > When the debug capability is enabled, it will present a debug device
> > through the debug port. This debug device is fully compliant with the
> > USB3 framework, and it can be enumerated by a debug host on the other
> > end of the USB link. As soon as the debug device is configured, a TTY
> > serial device named /dev/ttyDBC0 will be created.
> >
> > One use of this link is running a login service on the debug target.
> > Hence it can be remote accessed by a debug host. Another use case can
> > probably be found in servers. It provides a peer-to-peer USB link
> > between two host-only machines. This provides a reasonable out-of-band
> > communication method between two servers.
> >
> > Signed-off-by: Lu Baolu <baolu.lu@xxxxxxxxxxxxxxx>
> > ---
> >  .../ABI/testing/sysfs-bus-pci-drivers-xhci_hcd     |   25 +
> >  drivers/usb/host/Kconfig                           |    9 +
> >  drivers/usb/host/Makefile                          |    5 +
> >  drivers/usb/host/xhci-dbgcap.c                     | 1016 ++++++++++++++++++++
> >  drivers/usb/host/xhci-dbgcap.h                     |  247 +++++
> >  drivers/usb/host/xhci-dbgtty.c                     |  586 +++++++++++
> >  drivers/usb/host/xhci-trace.h                      |   60 ++
> >  drivers/usb/host/xhci.c                            |   10 +
> >  drivers/usb/host/xhci.h                            |    1 +
> >  9 files changed, 1959 insertions(+)
> >  create mode 100644 Documentation/ABI/testing/sysfs-bus-pci-drivers-xhci_hcd
> >  create mode 100644 drivers/usb/host/xhci-dbgcap.c
> >  create mode 100644 drivers/usb/host/xhci-dbgcap.h
> >  create mode 100644 drivers/usb/host/xhci-dbgtty.c
> >
> 
> [snip]
> 
> > +#define DBC_VENDOR_ID			0x1d6b	/* Linux Foundation 0x1d6b */
> > +#define DBC_PRODUCT_ID			0x0004	/* device 0004 */
> >
> 
> The DbC (xHCI DeBug Capability) is an optional functionality in
> some xHCI host controllers. It will present a super-speed debug
> device through the debug port after it is enabled.
> 
> The DbC register set defines an interface for system software
> to specify the vendor id and product id of the debug device.
> These two values will be presented by the debug device in its
> device descriptor idVendor and idProduct fields.
> 
> Microsoft Windows have a well established protocol for
> debugging over DbC. And it assigns below values for its use.
> 
> USB\VID_045E&PID_062D.DeviceDesc="Microsoft USB Debug Target"
> 
> I'm going to use 0x1d6b/0x0004 value pair for DbC use in
> Linux. Do you approve me to do so?

No.  Why can't you use the same ids as Windows?  This is implementing
the same protocol, right?

If you have to use a OS-specific id, I can give you a new one, but 0004
is not ok to use for this.

thanks,

greg k-h