Re: MCP251x SPI CAN controller on Cavium ThunderX

[Marc Kleine-Budde]

On 11/15/2017 01:07 PM, Jan Glauber wrote:
> On Wed, Nov 15, 2017 at 11:54:20AM +0100, Marc Kleine-Budde wrote:
>> On 11/14/2017 01:02 PM, Mark Brown wrote:
>>> On Mon, Nov 13, 2017 at 01:17:42PM -0800, Tim Harvey wrote:
>>>
>>>> When a register is read from the mcp251x driver the
>>>> octeon_spi_do_transfer() gets a spi_message with a single spi_xfer of
>>>> len=3, a tx_buf, and an rx_buf which I believe is supposed to shift
>>>> out 3 bytes out MOSI and shift in 3 bytes from MISO where the last
>>>> byte shifted in would be the response.
>>>
>>> No, that will simultaneously transmit and recieve three bytes.
>>
>> That's what the driver supposed to do.
>>
>>> If you want to transmit two bytes and then recieve one byte you need
>>> two xfers, one with a len of 2 and a tx_buf, the other with a len of
>>> 1 and a rx_buf.
>> To read a register (mcp251x_read_reg()) the mcp251x does a 3 byte full
>> duplex transfer. The first byte send is the command (read register) the
>> second byte the register number the third byte is a dummy. The first 2
>> bytes received are ignored the 3rd byte is the register contents.
> 
> To support this full duplex transfer the Cavium SPI controller needs
> to know the receive lenght before setting up the transaction.
> 
> spi_transfer only includes the total length, so I don't see how this
> should work.

It's a standard 3 byte full duplex transfer. Three bytes are send while
three bytes are received.

> static int mcp251x_spi_trans(struct spi_device *spi, int len)
> {
> 	struct mcp251x_priv *priv = spi_get_drvdata(spi);
> 	struct spi_transfer t = {
> 		.tx_buf = priv->spi_tx_buf,
> 		.rx_buf = priv->spi_rx_buf,
> 		.len = len,
> 		.cs_change = 0,
> 	};
> 	struct spi_message m;
> 	int ret;
> 
> 	spi_message_init(&m);
> 
> 	if (mcp251x_enable_dma) {
> 		t.tx_dma = priv->spi_tx_dma;
> 		t.rx_dma = priv->spi_rx_dma;
> 		m.is_dma_mapped = 1;
> 	}
> 
> 	spi_message_add_tail(&t, &m);
> 
> 	ret = spi_sync(spi, &m);
> 	if (ret)
> 		dev_err(&spi->dev, "spi transfer failed: ret = %d\n", ret);
> 	return ret;
> }

mcp251x_spi_trans() is called with len=3,
priv->spi_tx_buf and priv->spi_rx_buf point to previously allocared memory

priv->spi_tx_buf has been filled before calling mcp251x_spi_trans().

Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

Attachment: signature.asc
Description: OpenPGP digital signature