Re: [PATCH 5/8] ASoC: uniphier: add support for UniPhier AIO driver

[Mark Brown]

On Wed, Nov 22, 2017 at 08:43:18PM +0900, Katsuhiro Suzuki wrote:

>  sound/soc/uniphier/Makefile      |   4 +
>  sound/soc/uniphier/aio-core.c    | 368 +++++++++++++++++++++
>  sound/soc/uniphier/aio-dma.c     | 266 +++++++++++++++
>  sound/soc/uniphier/aio-regctrl.c | 699 +++++++++++++++++++++++++++++++++++++++
>  sound/soc/uniphier/aio-regctrl.h | 495 +++++++++++++++++++++++++++
>  sound/soc/uniphier/aio.h         | 261 +++++++++++++++

Please split this up more, it looks like there's at least two or three
drivers in here and it winds up being quite large.  There's at least a
DMA and a DAI driver.  Looking through this my overall impression is
that this is a fairly large and complex audio subsystem with some DSP
and routing capacity which is being handled in a board specific fashion
rather than generically but it's kind of hard to tell as there's not
much description of what's going on so I'm needing to reverse engineer
things from the driver.

The code itself looks fairly clean, it's mainly a case of trying to
figure out if it's doing what it's supposed to with the limited
documentation.

> +int uniphier_aio_hw_params(struct snd_pcm_substream *substream,
> +			   struct snd_pcm_hw_params *params,
> +			   struct snd_soc_dai *dai)
> +{
> +	struct uniphier_aio *aio = uniphier_priv(dai);
> +	struct uniphier_aio_sub *sub = &aio->sub[substream->stream];
> +
> +	sub->params = *params;
> +	sub->setting = 1;

So we don't validate the params at all?

> +	uniphier_aio_port_reset(sub);
> +	uniphier_aio_srcport_reset(sub);

Is there a mux in the SoC here?

> +static const struct of_device_id uniphier_aio_of_match[] = {
> +#ifdef CONFIG_SND_SOC_UNIPHIER_LD11
> +	{
> +		.compatible = "socionext,uniphier-ld11-aio",
> +		.data = &uniphier_aio_ld11_spec,
> +	},
> +	{
> +		.compatible = "socionext,uniphier-ld20-aio",
> +		.data = &uniphier_aio_ld20_spec,
> +	},
> +#endif /* CONFIG_SND_SOC_UNIPHIER_LD11 */

Why is there an ifdef here?  There's no other conditional code in here,
it seems pointless.

> +		for (j = 0; j < ARRAY_SIZE(aio->sub); j++) {
> +			struct uniphier_aio_sub *sub = &aio->sub[j];
> +
> +			if (!sub->running)
> +				continue;
> +
> +			spin_lock(&sub->spin);
> +			uniphier_aio_rb_sync(sub);
> +			uniphier_aio_rb_clear_int(sub);
> +			spin_unlock(&sub->spin);

It's not 100% obvious what this does...  a comment might help.

> +int uniphier_aio_chip_init(struct uniphier_aio_chip *chip)
> +{
> +	struct regmap *r = chip->regmap;
> +
> +	regmap_update_bits(r, A2APLLCTR0,
> +			   A2APLLCTR0_APLLXPOW_MASK,
> +			   A2APLLCTR0_APLLXPOW_PWON);
> +
> +	regmap_update_bits(r, A2APLLCTR1, A2APLLCTR1_APLL_MASK,
> +			   A2APLLCTR1_APLLF2_33MHZ | A2APLLCTR1_APLLA2_33MHZ |
> +			   A2APLLCTR1_APLLF1_36MHZ | A2APLLCTR1_APLLA1_36MHZ);
> +
> +	regmap_update_bits(r, A2EXMCLKSEL0,
> +			   A2EXMCLKSEL0_EXMCLK_MASK,
> +			   A2EXMCLKSEL0_EXMCLK_OUTPUT);
> +
> +	regmap_update_bits(r, A2AIOINPUTSEL, A2AIOINPUTSEL_RXSEL_MASK,
> +			   A2AIOINPUTSEL_RXSEL_PCMI1_HDMIRX1 |
> +			   A2AIOINPUTSEL_RXSEL_PCMI2_SIF |
> +			   A2AIOINPUTSEL_RXSEL_PCMI3_EVEA |
> +			   A2AIOINPUTSEL_RXSEL_IECI1_HDMIRX1);

This definitely looks like there's some clocking and audio routing
within the SoC which should be exposed to userspace, or at the very
least machine driver configuration rather than being hard coded.

> +	switch (pc) {
> +	case IEC61937_PC_AC3:
> +		repet = OPORTMXREPET_STRLENGTH_AC3 |
> +			OPORTMXREPET_PMLENGTH_AC3;
> +		pause |= OPORTMXPAUDAT_PAUSEPD_AC3;
> +		break;
> +	case IEC61937_PC_MPA:
> +		repet = OPORTMXREPET_STRLENGTH_MPA |
> +			OPORTMXREPET_PMLENGTH_MPA;
> +		pause |= OPORTMXPAUDAT_PAUSEPD_MPA;
> +		break;
> +	case IEC61937_PC_MP3:
> +		repet = OPORTMXREPET_STRLENGTH_MP3 |
> +			OPORTMXREPET_PMLENGTH_MP3;
> +		pause |= OPORTMXPAUDAT_PAUSEPD_MP3;
> +		break;

This looks awfully like compressed audio support...  should there be
integration with the compressed audio API/

Attachment: signature.asc
Description: PGP signature