Re: [PATCH v4 4/8] arm: OMAP: Move dmtimer driver out of plat-omap to drivers under clocksource

[Daniel Lezcano]

On 01/12/2017 06:16, Keerthy wrote:
> Move the dmtimer driver out of plat-omap to clocksource.
> So that non-omap devices also could use this.
> 
> No Code changes done to the driver file.
> 
> Signed-off-by: Keerthy <j-keerthy@xxxxxx>
> Reviewed-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
> ---
> 
> Changes in v3:
> 
>   * Added Sebastian's Reviewed-by.
> 
> Changes in v2:
> 
>   * No code changes in this v2 version. Only enhanced patch
>     statistics for renames.
> 
>  arch/arm/plat-omap/Kconfig                            | 6 ------
>  arch/arm/plat-omap/Makefile                           | 1 -
>  drivers/clocksource/Kconfig                           | 6 ++++++
>  drivers/clocksource/Makefile                          | 1 +
>  {arch/arm/plat-omap => drivers/clocksource}/dmtimer.c | 0
>  5 files changed, 7 insertions(+), 7 deletions(-)
>  rename {arch/arm/plat-omap => drivers/clocksource}/dmtimer.c (100%)

Take the opportunity to rename it timer-dm.c

> diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
> index 7276afe..afc1a1d 100644
> --- a/arch/arm/plat-omap/Kconfig
> +++ b/arch/arm/plat-omap/Kconfig
> @@ -106,12 +106,6 @@ config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
>  	help
>  	  PPA routine service ID for setting L2 auxiliary control register.
>  
> -config OMAP_DM_TIMER
> -	bool "Use dual-mode timer"
> -	depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
> -	help
> -	 Select this option if you want to use OMAP Dual-Mode timers.
> -
>  config OMAP_SERIAL_WAKE
>  	bool "Enable wake-up events for serial ports"
>  	depends on ARCH_OMAP1 && OMAP_MUX
> diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile
> index 47e1867..7215ada 100644
> --- a/arch/arm/plat-omap/Makefile
> +++ b/arch/arm/plat-omap/Makefile
> @@ -9,5 +9,4 @@ obj-y := sram.o dma.o counter_32k.o
>  
>  # omap_device support (OMAP2+ only at the moment)
>  
> -obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o
>  obj-$(CONFIG_OMAP_DEBUG_LEDS) += debug-leds.o
> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> index c729a88..4da66cf 100644
> --- a/drivers/clocksource/Kconfig
> +++ b/drivers/clocksource/Kconfig
> @@ -46,6 +46,12 @@ config DIGICOLOR_TIMER
>  	help
>  	  Enables the support for the digicolor timer driver.
>  
> +config OMAP_DM_TIMER
> +	bool "Use dual-mode timer"
> +	depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
> +	help
> +	 Select this option if you want to use Dual-Mode timers.
> +

So in the clocksource directory the rule is the following:

The config option is silent except if COMPILE_TEST is set.

It is the Kconfig's platform which select the driver so there is no deps
on the ARCH.

config OMAP_DM_TIMER
	bool "Use dual-mode timer" if COMPILE_TEST
	help
	 Select this option if you want to use Dual-Mode timers.

Here you will have to make sure the driver compiles on x86.

>  config DW_APB_TIMER
>  	bool "DW APB timer driver" if COMPILE_TEST
>  	help
> diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
> index 72711f1..b077076 100644
> --- a/drivers/clocksource/Makefile
> +++ b/drivers/clocksource/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_EM_TIMER_STI)	+= em_sti.o
>  obj-$(CONFIG_CLKBLD_I8253)	+= i8253.o
>  obj-$(CONFIG_CLKSRC_MMIO)	+= mmio.o
>  obj-$(CONFIG_DIGICOLOR_TIMER)	+= timer-digicolor.o
> +obj-$(CONFIG_OMAP_DM_TIMER)	+= dmtimer.o
>  obj-$(CONFIG_DW_APB_TIMER)	+= dw_apb_timer.o
>  obj-$(CONFIG_DW_APB_TIMER_OF)	+= dw_apb_timer_of.o
>  obj-$(CONFIG_FTTMR010_TIMER)	+= timer-fttmr010.o
> diff --git a/arch/arm/plat-omap/dmtimer.c b/drivers/clocksource/dmtimer.c
> similarity index 100%
> rename from arch/arm/plat-omap/dmtimer.c
> rename to drivers/clocksource/dmtimer.c
> 


-- 
 <http://www.linaro.org/> Linaro.org â Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog