Re: [PATCH v2 05/16] remoteproc: modify rproc_handle_carveout to support preallocated region

[Bjorn Andersson]

On Thu 30 Nov 08:46 PST 2017, Loic Pallardy wrote:

> In current version rproc_handle_carveout function support only dynamic
> region allocation.
> This patch extends rproc_handle_carveout function to support different carveout
> configurations:
> - fixed DA and fixed PA: check if already part of pre-registered carveouts
> (platform driver). If no, return error.
> - fixed DA and any PA: check if already part of pre-allocated carveouts
> (platform driver). If not found and rproc supports iommu, continue with
> dynamic allocation (DA will be used for iommu programming), else return
> error as no way to force DA.
> - any DA and any PA: use original dynamic allocation
> 
> Signed-off-by: Loic Pallardy <loic.pallardy@xxxxxx>
> ---
>  drivers/remoteproc/remoteproc_core.c | 40 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/drivers/remoteproc/remoteproc_core.c b/drivers/remoteproc/remoteproc_core.c
> index 78525d1..515a17a 100644
> --- a/drivers/remoteproc/remoteproc_core.c
> +++ b/drivers/remoteproc/remoteproc_core.c
> @@ -184,6 +184,10 @@ void *rproc_da_to_va(struct rproc *rproc, u64 da, int len)
>  	struct rproc_mem_entry *carveout;
>  	void *ptr = NULL;
>  
> +	/*
> +	 * da_to_va platform driver is deprecated. Driver should register
> +	 * carveout thanks to rproc_add_carveout function
> +	 */

I think this comment is unrelated to the rest of this patch. I also
think that at the end of the carveout-rework we should have a patch
removing this ops.

>  	if (rproc->ops->da_to_va) {
>  		ptr = rproc->ops->da_to_va(rproc, da, len);
>  		if (ptr)
> @@ -677,6 +681,7 @@ static int rproc_handle_carveout(struct rproc *rproc,
>  	struct rproc_mem_entry *carveout, *mapping;
>  	struct device *dev = &rproc->dev;
>  	dma_addr_t dma;
> +	phys_addr_t pa;
>  	void *va;
>  	int ret;
>  
> @@ -698,6 +703,41 @@ static int rproc_handle_carveout(struct rproc *rproc,
>  	if (!carveout)
>  		return -ENOMEM;
>  
> +	/* Check carveout rsc already part of a registered carveout */
> +	if (rsc->da != FW_RSC_ADDR_ANY) {

As mentioned before, I consider it perfectly viable for rsc->da to be
ANY and the driver providing a fixed carveout.

> +		va = rproc_find_carveout_by_da(rproc, rsc->da, rsc->len);
> +
> +		if (va) {

In a system with an iommu it's possible that rsc->len is larger than
some carveout->len and va is NULL here so we fall through, allocate some
memory and remap a segment of the carveout. (Or hopefully fails
attempting).

> +			/* Registered region found */
> +			pa = rproc_va_to_pa(va);
> +			if (rsc->pa != FW_RSC_ADDR_ANY && rsc->pa != (u32)pa) {
> +				/* Carveout doesn't match request */
> +				dev_err(dev->parent,
> +					"Failed to find carveout fitting da and pa\n");
> +				return -ENOMEM;
> +			}
> +
> +			/* Update rsc table with physical address */
> +			rsc->pa = (u32)pa;
> +
> +			/* Update carveouts list */
> +			carveout->va = va;
> +			carveout->len = rsc->len;
> +			carveout->da = rsc->da;
> +			carveout->priv = (void *)CARVEOUT_RSC;
> +
> +			list_add_tail(&carveout->node, &rproc->carveouts);

rproc_find_carveout_by_da() will return a reference into a carveout, now
we add another overlapping carveout into the same list.


I think it would be saner to not allow the resource table to describe
subsets of carveouts registered by the driver.

In which case this would better find a carveout by name or exact da,
then check that the pa, da, len and rsc->flags are adequate.

> +
> +			return 0;
> +		}
> +
> +		if (!rproc->domain) {

Currently this function ignore invalid values of da when !domain, so I
think it would be good you can submit this sanity check in it's own
patch so that anyone bisecting this would know why their broken firmware
suddenly isn't loadable.

> +			dev_err(dev->parent,
> +				"Bad carveout rsc configuration\n");
> +			return -ENOMEM;
> +		}
> +	}
> +

Regards,
Bjorn