Re: [PATCH v3] iio: adc: ina2xx: Make calibration register value fixed

[Jonathan Cameron]

On Fri, 15 Dec 2017 08:59:23 +0100
Maciej Purski <m.purski@xxxxxxxxxxx> wrote:

> Calibration register is used for calculating current register in
> hardware according to datasheet:
> current = shunt_volt * calib_register / 2048 (ina 226)
> current = shunt_volt * calib_register / 4096 (ina 219)
> 
> Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
> order to avoid truncation error and provide best precision allowed
> by shunt_voltage measurement. Make current scale value follow changes
> of shunt_resistor from sysfs as calib_register value is now fixed.
> 
> Power_lsb value should also follow shunt_resistor changes as stated in
> datasheet:
> power_lsb = 25 * current_lsb (ina 226)
> power_lsb = 20 * current_lsb (ina 219)
> 
> This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394
> 
> Signed-off-by: Maciej Purski <m.purski@xxxxxxxxxxx>
Looks good to me. I'll let it sit for Stefan to have a change to look at it though.
If it looks like I've forgotten it by early Jan do give me a kick.

Thanks,

Jonathan
> 
> ---
> Changes in v3:
> - remove variable current_lsb and calculate it on each read of current
>   and power scale value
> - update comments
> 
> Changes in v2:
> - rebase on top of the latest next
> - remove a redundant variable - power_lsb_uW
> - fix comments
> ---
>  drivers/iio/adc/ina2xx-adc.c | 56 +++++++++++++++++++++-----------------------
>  1 file changed, 27 insertions(+), 29 deletions(-)
> 
> diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
> index ddf8781..3488100 100644
> --- a/drivers/iio/adc/ina2xx-adc.c
> +++ b/drivers/iio/adc/ina2xx-adc.c
> @@ -124,11 +124,11 @@ enum ina2xx_ids { ina219, ina226 };
>  
>  struct ina2xx_config {
>  	u16 config_default;
> -	int calibration_factor;
> +	int calibration_value;
>  	int shunt_voltage_lsb;	/* nV */
>  	int bus_voltage_shift;	/* position of lsb */
>  	int bus_voltage_lsb;	/* uV */
> -	int power_lsb;		/* uW */
> +	int power_lsb_factor;
>  	enum ina2xx_ids chip_id;
>  };
>  
> @@ -149,20 +149,20 @@ struct ina2xx_chip_info {
>  static const struct ina2xx_config ina2xx_config[] = {
>  	[ina219] = {
>  		.config_default = INA219_CONFIG_DEFAULT,
> -		.calibration_factor = 40960000,
> +		.calibration_value = 4096,
>  		.shunt_voltage_lsb = 10000,
>  		.bus_voltage_shift = INA219_BUS_VOLTAGE_SHIFT,
>  		.bus_voltage_lsb = 4000,
> -		.power_lsb = 20000,
> +		.power_lsb_factor = 20,
>  		.chip_id = ina219,
>  	},
>  	[ina226] = {
>  		.config_default = INA226_CONFIG_DEFAULT,
> -		.calibration_factor = 5120000,
> +		.calibration_value = 2048,
>  		.shunt_voltage_lsb = 2500,
>  		.bus_voltage_shift = 0,
>  		.bus_voltage_lsb = 1250,
> -		.power_lsb = 25000,
> +		.power_lsb_factor = 25,
>  		.chip_id = ina226,
>  	},
>  };
> @@ -228,15 +228,17 @@ static int ina2xx_read_raw(struct iio_dev *indio_dev,
>  			return IIO_VAL_FRACTIONAL;
>  
>  		case INA2XX_POWER:
> -			/* processed (mW) = raw*lsb (uW) / 1000 */
> -			*val = chip->config->power_lsb;
> -			*val2 = 1000;
> +			/* processed (mW) = raw * factor * current_lsb (mW)*/
> +			*val = chip->config->power_lsb_factor *
> +			       chip->config->shunt_voltage_lsb;
> +			*val2 = chip->shunt_resistor_uohm;
>  			return IIO_VAL_FRACTIONAL;
>  
>  		case INA2XX_CURRENT:
> -			/* processed (mA) = raw (mA) */
> -			*val = 1;
> -			return IIO_VAL_INT;
> +			/* processed (mA) = raw * lsb ([nV] / [uOhm] = [mA]) */
> +			*val = chip->config->shunt_voltage_lsb;
> +			*val2 = chip->shunt_resistor_uohm;
> +			return IIO_VAL_FRACTIONAL;
>  		}
>  
>  	case IIO_CHAN_INFO_HARDWAREGAIN:
> @@ -541,25 +543,26 @@ static ssize_t ina2xx_allow_async_readout_store(struct device *dev,
>  }
>  
>  /*
> - * Set current LSB to 1mA, shunt is in uOhms
> - * (equation 13 in datasheet). We hardcode a Current_LSB
> - * of 1.0 x10-3. The only remaining parameter is RShunt.
> - * There is no need to expose the CALIBRATION register
> - * to the user for now. But we need to reset this register
> - * if the user updates RShunt after driver init, e.g upon
> - * reading an EEPROM/Probe-type value.
> + * Calibration register is set to the best value, which eliminates
> + * truncation errors on calculating current register in hardware.
> + * According to datasheet (INA 226: eq. 3, INA219: eq. 4) the best values
> + * are 2048 for ina226 and 4096 for ina219. They are hardcoded as
> + * calibration_value.
>   */
>  static int ina2xx_set_calibration(struct ina2xx_chip_info *chip)
>  {
> -	u16 regval = DIV_ROUND_CLOSEST(chip->config->calibration_factor,
> -				   chip->shunt_resistor_uohm);
> -
> -	return regmap_write(chip->regmap, INA2XX_CALIBRATION, regval);
> +	return regmap_write(chip->regmap, INA2XX_CALIBRATION,
> +			    chip->config->calibration_value);
>  }
>  
> +/*
> + * As the calibration register is fixed, the product of current_lsb
> + * and shunt_resistor should also be fixed and equal
> + * to shunt_voltage_lsb. Current_lsb will be calculated in read_raw()
> + */
>  static int set_shunt_resistor(struct ina2xx_chip_info *chip, unsigned int val)
>  {
> -	if (val <= 0 || val > chip->config->calibration_factor)
> +	if (val == 0 || val > INT_MAX)
>  		return -EINVAL;
>  
>  	chip->shunt_resistor_uohm = val;
> @@ -592,11 +595,6 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
>  	if (ret)
>  		return ret;
>  
> -	/* Update the Calibration register */
> -	ret = ina2xx_set_calibration(chip);
> -	if (ret)
> -		return ret;
> -
>  	return len;
>  }
>