Re: [linux-sunxi] [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

[Priit Laes]

On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> Add binding documentation for Allwinner V3s CSI.
> 
> Signed-off-by: Yong Deng <yong.deng@xxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/media/sun6i-csi.txt        | 51 ++++++++++++++++++++++
>  1 file changed, 51 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> new file mode 100644
> index 0000000..b5bfe3f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> @@ -0,0 +1,51 @@
> +Allwinner V3s Camera Sensor Interface
> +------------------------------

Not sure whether syntax for these files is proper reStructuredText/Markdown,
but the underline-ish style expects the title and underline having same length.

> +
> +Required properties:
> +  - compatible: value must be "allwinner,sun8i-v3s-csi"
> +  - reg: base address and size of the memory-mapped region.
> +  - interrupts: interrupt associated to this IP
> +  - clocks: phandles to the clocks feeding the CSI
> +    * bus: the CSI interface clock
> +    * mod: the CSI module clock
> +    * ram: the CSI DRAM clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandles to the reset line driving the CSI
> +
> +- ports: A ports node with endpoint definitions as defined in
> +  Documentation/devicetree/bindings/media/video-interfaces.txt.
> +  Currently, the driver only support the parallel interface. So, a single port
^^ supports
> +  node with one endpoint and parallel bus is supported.
> +
> +Example:
> +
> +	csi1: csi@1cb4000 {
> +		compatible = "allwinner,sun8i-v3s-csi";
> +		reg = <0x01cb4000 0x1000>;
> +		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&ccu CLK_BUS_CSI>,
> +			 <&ccu CLK_CSI1_SCLK>,
> +			 <&ccu CLK_DRAM_CSI>;
> +		clock-names = "bus", "mod", "ram";
> +		resets = <&ccu RST_BUS_CSI>;
> +
> +		port {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			/* Parallel bus endpoint */
> +			csi1_ep: endpoint {
> +				remote-endpoint = <&adv7611_ep>;
> +				bus-width = <16>;
> +				data-shift = <0>;
> +
> +				/* If hsync-active/vsync-active are missing,
> +				   embedded BT.656 sync is used */
> +				hsync-active = <0>; /* Active low */
> +				vsync-active = <0>; /* Active low */
> +				data-active = <1>;  /* Active high */
> +				pclk-sample = <1>;  /* Rising */
> +			};
> +		};
> +	};
> +
> -- 
> 1.8.3.1
> 
> -- 
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/d/optout.