Re: [PATCH v5 2/2] PCI: mediatek: Set up class type and vendor ID for MT7622

[Honghui Zhang]

On Wed, 2017-12-27 at 12:45 -0600, Bjorn Helgaas wrote:
> On Wed, Dec 27, 2017 at 08:59:54AM +0800, honghui.zhang@xxxxxxxxxxxx wrote:
> > From: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
> > 
> > The hardware default value of IDs and class type is not correct,
> > fix that by setup the correct values before start up.
> > 
> > Signed-off-by: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
> > ---
> >  drivers/pci/host/pcie-mediatek.c | 12 ++++++++++++
> >  include/linux/pci_ids.h          |  2 ++
> >  2 files changed, 14 insertions(+)
> > 
> > diff --git a/drivers/pci/host/pcie-mediatek.c b/drivers/pci/host/pcie-mediatek.c
> > index fc29a9a..62aac0ea 100644
> > --- a/drivers/pci/host/pcie-mediatek.c
> > +++ b/drivers/pci/host/pcie-mediatek.c
> > @@ -74,6 +74,10 @@
> >  
> >  /* PCIe V2 per-port registers */
> >  #define PCIE_MSI_VECTOR		0x0c0
> > +
> > +#define PCIE_CONF_ID		0x100
> > +#define PCIE_CONF_CLASS		0x104
> > +
> >  #define PCIE_INT_MASK		0x420
> >  #define INTX_MASK		GENMASK(19, 16)
> >  #define INTX_SHIFT		16
> > @@ -393,6 +397,14 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
> >  		val |= PCIE_CSR_LTSSM_EN(port->slot) |
> >  		       PCIE_CSR_ASPM_L1_EN(port->slot);
> >  		writel(val, pcie->base + PCIE_SYS_CFG_V2);
> > +
> > +		/* Set up vendor ID and device ID for MT7622*/
> > +		val = PCI_VENDOR_ID_MEDIATEK;
> > +		writel(val, port->base + PCIE_CONF_ID);
> > +
> > +		/* Set up class code for MT7622 */
> > +		val = PCI_CLASS_BRIDGE_PCI << 16;
> > +		writel(val, port->base + PCIE_CONF_CLASS);
> 
> 1) Your comments mention MT7622 specifically, but this code is run for
> both mt2712-pcie and mt7622-pcie.  If this code is safe and necessary
> for both mt2712-pcie and mt7622-pcie, please remove the mention of
> MT7622.

Hmm, the code snippet added here will only be executed by MT7622, since
MT2712 will not enter this  "if (pcie->base) {"  condition.
Should the mention of MT7622 must be removed in this case?

> 
> 2) The first comment mentions both "vendor ID and device ID" but you
> don't write the device ID.  Since this code applies to both
> mt2712-pcie and mt7622-pcie, my guess is that you don't *want* to
> write the device ID.  If that's the case, please fix the comment.
> 

My bad, I did not check the comments carefully.
Thanks.

> 3) If you only need to set the vendor ID, you're performing a 32-bit
> write (writel()) to update a 16-bit value.  Please use writew()
> instead.
> 

Ok, thanks, I guess I could use the following code snippet in the next
version:
val = readl(port->base + PCIE_CONF_VENDOR_ID)
val &= ~GENMASK(15, 0);
val |= PCI_VENDOR_ID_MEDIATEK;
writel(val, port->base + PCIE_CONF_VENDOR_ID);

> 4) If you only need to set the vendor ID, please use a definition like
> "PCIE_CONF_VENDOR_ID" instead of the ambiguous "PCIE_CONF_ID".
> 
> 5) If you only need to set the vendor ID, please update the changelog
> to mention "vendor ID" specifically instead of the ambiguous "IDs".

> 6) Please add a space before the closing "*/" of the first comment.
> 
> 7) PCI_CLASS_BRIDGE_PCI is for a PCI-to-PCI bridge, i.e., one that has
> PCI on both the primary (upstream) side and the secondary (downstream)
> side.  That kind of bridge has a type 1 config header (see
> PCI_HEADER_TYPE) and the PCI_PRIMARY_BUS and PCI_SECONDARY_BUS
> registers tell us the bus number of the primary and secondary sides.
> 
> I don't believe this device is a PCI-to-PCI bridge.  I think it's a
> *host* bridge that has some non-PCI interface on the upstream side and
> should have a type 0 config header.  If that's the case you should use
> PCI_CLASS_BRIDGE_HOST instead.
> 

Thanks very much for your help with the review, I will fix the other
issue in the next version.

> >  	}
> >  
> >  	/* Assert all reset signals */
> > diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
> > index ab20dc5..2480b0e 100644
> > --- a/include/linux/pci_ids.h
> > +++ b/include/linux/pci_ids.h
> > @@ -2113,6 +2113,8 @@
> >  
> >  #define PCI_VENDOR_ID_MYRICOM		0x14c1
> >  
> > +#define PCI_VENDOR_ID_MEDIATEK		0x14c3
> > +
> >  #define PCI_VENDOR_ID_TITAN		0x14D2
> >  #define PCI_DEVICE_ID_TITAN_010L	0x8001
> >  #define PCI_DEVICE_ID_TITAN_100L	0x8010
> > -- 
> > 2.6.4
> >