[PATCH V2 3/5] usb: serial: f81534: add output pin control

[Ji-Ze Hong (Peter Hong)]

The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@xxxxxxxxx>
---
V2:
	1: Fix for space between brace.
	2: Remain the old pin control method.

 drivers/usb/serial/f81534.c | 67 ++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 66 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 8a778bc1d492..7f175f39a171 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -52,6 +52,7 @@
 #define F81534_CUSTOM_NO_CUSTOM_DATA	0xff
 #define F81534_CUSTOM_VALID_TOKEN	0xf0
 #define F81534_CONF_OFFSET		1
+#define F81534_CONF_GPIO_OFFSET		4
 
 #define F81534_MAX_DATA_BLOCK		64
 #define F81534_MAX_BUS_RETRY		20
@@ -164,6 +165,23 @@ struct f81534_port_private {
 	u8 phy_num;
 };
 
+struct f81534_pin_data {
+	const u16 reg_addr;
+	const u16 reg_mask;
+};
+
+struct f81534_port_out_pin {
+	struct f81534_pin_data pin[3];
+};
+
+/* Pin output value for M2/M1/M0(SD) */
+static const struct f81534_port_out_pin f81534_port_out_pins[] = {
+	 { { {0x2ae8, BIT(7)}, {0x2a90, BIT(5)}, {0x2a90, BIT(4) } } },
+	 { { {0x2ae8, BIT(6)}, {0x2ae8, BIT(0)}, {0x2ae8, BIT(3) } } },
+	 { { {0x2a90, BIT(0)}, {0x2ae8, BIT(2)}, {0x2a80, BIT(6) } } },
+	 { { {0x2a90, BIT(3)}, {0x2a90, BIT(2)}, {0x2a90, BIT(1) } } },
+};
+
 static u32 const baudrate_table[] = {115200, 921600, 1152000, 1500000};
 static u8 const clock_table[] = {F81534_CLK_1_846_MHZ, F81534_CLK_14_77_MHZ,
 				F81534_CLK_18_46_MHZ, F81534_CLK_24_MHZ};
@@ -273,6 +291,22 @@ static int f81534_get_register(struct usb_serial *serial, u16 reg, u8 *data)
 	return status;
 }
 
+static int f81534_set_mask_register(struct usb_serial *serial, u16 reg,
+					u8 mask, u8 data)
+{
+	int status;
+	u8 tmp;
+
+	status = f81534_get_register(serial, reg, &tmp);
+	if (status)
+		return status;
+
+	tmp &= ~mask;
+	tmp |= (mask & data);
+
+	return f81534_set_register(serial, reg, tmp);
+}
+
 static int f81534_set_port_register(struct usb_serial_port *port, u16 reg,
 					u8 data)
 {
@@ -1278,6 +1312,37 @@ static void f81534_lsr_worker(struct work_struct *work)
 		dev_warn(&port->dev, "read LSR failed: %d\n", status);
 }
 
+static int f81534_set_port_output_pin(struct usb_serial_port *port)
+{
+	struct f81534_serial_private *serial_priv;
+	struct f81534_port_private *port_priv;
+	struct usb_serial *serial;
+	const struct f81534_port_out_pin *pins;
+	int status;
+	int i;
+	u8 value;
+	u8 idx;
+
+	serial = port->serial;
+	serial_priv = usb_get_serial_data(serial);
+	port_priv = usb_get_serial_port_data(port);
+
+	idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num;
+	value = serial_priv->conf_data[idx];
+	pins = &f81534_port_out_pins[port_priv->phy_num];
+
+	for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {
+		status = f81534_set_mask_register(serial,
+				pins->pin[i].reg_addr, pins->pin[i].reg_mask,
+				value & BIT(i) ? pins->pin[i].reg_mask : 0);
+		if (status)
+			return status;
+	}
+
+	dev_dbg(&port->dev, "Output pin (M0/M1/M2): %d\n", value);
+	return 0;
+}
+
 static int f81534_port_probe(struct usb_serial_port *port)
 {
 	struct f81534_serial_private *serial_priv;
@@ -1335,7 +1400,7 @@ static int f81534_port_probe(struct usb_serial_port *port)
 		break;
 	}
 
-	return 0;
+	return f81534_set_port_output_pin(port);
 }
 
 static int f81534_port_remove(struct usb_serial_port *port)
-- 
2.7.4