[PATCH net-next v5 4/4] net: mvpp2: 2500baseX support
From: Antoine Tenart
Date: Fri Jan 12 2018 - 02:55:16 EST
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@xxxxxxxxxxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
---
drivers/net/ethernet/marvell/mvpp2.c | 49 ++++++++++++++++++++++++++++--------
1 file changed, 39 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 257a6b99b4ca..38f9a79481c6 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4502,6 +4502,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
break;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4540,7 +4541,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4571,7 +4573,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4584,7 +4587,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4599,6 +4603,16 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
mvpp22_gop_unmask_irq(port);
}
+/* Sets the PHY mode of the COMPHY (which configures the serdes lanes).
+ *
+ * The PHY mode used by the PPv2 driver comes from the network subsystem, while
+ * the one given to the COMPHY comes from the generic PHY subsystem. Hence they
+ * differ.
+ *
+ * The COMPHY configures the serdes lanes regardless of the actual use of the
+ * lanes by the physical layer. This is why configurations like
+ * "PPv2 (2500BaseX) - COMPHY (2500SGMII)" are valid.
+ */
static int mvpp22_comphy_init(struct mvpp2_port *port)
{
enum phy_mode mode;
@@ -4612,6 +4626,9 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ mode = PHY_MODE_2500SGMII;
+ break;
case PHY_INTERFACE_MODE_10GKR:
mode = PHY_MODE_10GKR;
break;
@@ -4631,7 +4648,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
u32 val;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
val |= MVPP22_CTRL4_SYNC_BYPASS_DIS | MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
@@ -4647,7 +4665,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
}
val = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
- if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PORT_TYPE_MASK;
else
val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
@@ -4660,7 +4679,13 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
val |= MVPP2_GMAC_IN_BAND_AUTONEG;
- if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ /* Clear all fields we may want to explicitly set below */
+ val &= ~(MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_AN_SPEED_EN |
+ MVPP2_GMAC_AN_DUPLEX_EN);
+
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
/* 1000BaseX port cannot negotiate speed nor can it
* negotiate duplex: they are always operating with a
* fixed speed of 1000Mbps in full duplex, so force
@@ -4693,7 +4718,8 @@ static void mvpp2_port_mii_gmac_configure(struct mvpp2_port *port)
/* Configure the PCS and in-band AN */
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
} else if (phy_interface_mode_is_rgmii(port->phy_interface)) {
val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -4756,7 +4782,8 @@ static void mvpp2_port_mii_set(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
mvpp2_port_mii_gmac_configure(port);
else if (port->phy_interface == PHY_INTERFACE_MODE_10GKR)
mvpp2_port_mii_xlg_configure(port);
@@ -4834,7 +4861,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port)
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6048,7 +6076,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
--
2.14.3