[PATCH 1/2] mmc: sdhci: Add support for O2 eMMC HS200 mode

[ernest.zhang]

when eMMC used as boot device, the eMMC signaling voltage is tied to 1.8v
fixed output voltage, bios can set o2 sd host controller PCI configuration
register 0x308 bit4 to 1 to let host controller skip try 3.3.v signaling
voltage and direct use 1.8v singling voltage in eMMC initialize process.

Signed-off-by: ernest.zhang <ernest.zhang@xxxxxxxxxxxxxx>
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 20 +++++++++++++++++++-
 1 file changed, 19 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index 555970a29c94..8855a416ffd4 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -1,8 +1,9 @@
 /*
- * Copyright (C) 2013 BayHub Technology Ltd.
+ * Copyright (C) 2018 BayHub Technology Ltd.
  *
  * Authors: Peter Guo <peter.guo@xxxxxxxxxxxxxx>
  *          Adam Lee <adam.lee@xxxxxxxxxxxxx>
+ *          Ernest Zhang <ernest.zhang@xxxxxxxxxxxxx>
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -39,6 +40,7 @@
 #define O2_SD_MISC_CTRL4	0xFC
 #define O2_SD_TUNING_CTRL	0x300
 #define O2_SD_PLL_SETTING	0x304
+#define O2_SD_MISC_SETTING	0x308
 #define O2_SD_CLK_SETTING	0x328
 #define O2_SD_CAP_REG2		0x330
 #define O2_SD_CAP_REG0		0x334
@@ -53,6 +55,7 @@
 
 #define O2_SD_VENDOR_SETTING	0x110
 #define O2_SD_VENDOR_SETTING2	0x1C8
+#define O2_SD_HW_TUNING_ENABLE	BIT(4)
 
 static void o2_pci_set_baseclk(struct sdhci_pci_chip *chip, u32 value)
 {
@@ -184,6 +187,7 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 	struct sdhci_pci_chip *chip;
 	struct sdhci_host *host;
 	u32 reg;
+	int ret;
 
 	chip = slot->chip;
 	host = slot->host;
@@ -197,6 +201,20 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 		if (reg & 0x1)
 			host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
 
+		if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
+			ret = pci_read_config_dword(chip->pdev,
+						    O2_SD_MISC_SETTING, &reg);
+			if (ret)
+				return -EIO;
+			if (reg & (1 << 4)) {
+				pr_info("%s: emmc 1.8v flag is set, force 1.8v signaling voltage\n",
+				     mmc_hostname(host->mmc));
+				host->flags &= ~SDHCI_SIGNALING_330;
+				host->flags |= SDHCI_SIGNALING_180;
+			}
+		}
+
+
 		if (chip->pdev->device != PCI_DEVICE_ID_O2_FUJIN2)
 			break;
 		/* set dll watch dog timer */
-- 
2.14.1