[PATCH net-next 4/5] net: hns3: add ethtool -p support for fiber port

[Peng Li]

From: Jian Shen <shenjian15@xxxxxxxxxx>

Add led location support for fiber port. The led will keep blinking
when locating.

Signed-off-by: Jian Shen <shenjian15@xxxxxxxxxx>
Signed-off-by: Peng Li <lipeng321@xxxxxxxxxx>
---
 .../net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h |  20 ++++
 .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c    | 101 ++++++++++++++++-----
 2 files changed, 100 insertions(+), 21 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
index 1cd28e0..122f862 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h
@@ -227,6 +227,9 @@ enum hclge_opcode_type {
 
 	/* Mailbox cmd */
 	HCLGEVF_OPC_MBX_PF_TO_VF	= 0x2000,
+
+	/* Led command */
+	HCLGE_OPC_LED_STATUS_CFG	= 0xB000,
 };
 
 #define HCLGE_TQP_REG_OFFSET		0x80000
@@ -807,6 +810,23 @@ struct hclge_reset_cmd {
 #define HCLGE_NIC_CMQ_DESC_NUM		1024
 #define HCLGE_NIC_CMQ_DESC_NUM_S	3
 
+#define HCLGE_LED_PORT_SPEED_STATE_S	0
+#define HCLGE_LED_PORT_SPEED_STATE_M	GENMASK(5, 0)
+#define HCLGE_LED_ACTIVITY_STATE_S	0
+#define HCLGE_LED_ACTIVITY_STATE_M	GENMASK(1, 0)
+#define HCLGE_LED_LINK_STATE_S		0
+#define HCLGE_LED_LINK_STATE_M		GENMASK(1, 0)
+#define HCLGE_LED_LOCATE_STATE_S	0
+#define HCLGE_LED_LOCATE_STATE_M	GENMASK(1, 0)
+
+struct hclge_set_led_state_cmd {
+	u8 port_speed_led_config;
+	u8 link_led_config;
+	u8 activity_led_config;
+	u8 locate_led_config;
+	u8 rsv[20];
+};
+
 int hclge_cmd_init(struct hclge_dev *hdev);
 static inline void hclge_write_reg(void __iomem *base, u32 reg, u32 value)
 {
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index 73caf06..039c90b 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -5819,6 +5819,34 @@ static void hclge_get_regs(struct hnae3_handle *handle, u32 *version,
 			"Get 64 bit register failed, ret = %d.\n", ret);
 }
 
+static int hclge_set_led_status_sfp(struct hclge_dev *hdev, u8 speed_led_status,
+				    u8 act_led_status, u8 link_led_status,
+				    u8 locate_led_status)
+{
+	struct hclge_set_led_state_cmd *req;
+	struct hclge_desc desc;
+	int ret;
+
+	hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_LED_STATUS_CFG, false);
+
+	req = (struct hclge_set_led_state_cmd *)desc.data;
+	hnae_set_field(req->port_speed_led_config, HCLGE_LED_PORT_SPEED_STATE_M,
+		       HCLGE_LED_PORT_SPEED_STATE_S, speed_led_status);
+	hnae_set_field(req->link_led_config, HCLGE_LED_ACTIVITY_STATE_M,
+		       HCLGE_LED_ACTIVITY_STATE_S, act_led_status);
+	hnae_set_field(req->activity_led_config, HCLGE_LED_LINK_STATE_M,
+		       HCLGE_LED_LINK_STATE_S, link_led_status);
+	hnae_set_field(req->locate_led_config, HCLGE_LED_LOCATE_STATE_M,
+		       HCLGE_LED_LOCATE_STATE_S, locate_led_status);
+
+	ret = hclge_cmd_send(&hdev->hw, &desc, 1);
+	if (ret)
+		dev_err(&hdev->pdev->dev,
+			"Send set led state cmd error, ret =%d\n", ret);
+
+	return ret;
+}
+
 static int hclge_set_led_status_phy(struct phy_device *phydev, int value)
 {
 	int ret, cur_page;
@@ -5871,6 +5899,12 @@ static int hclge_get_led_status_phy(struct phy_device *phydev, int *value)
 	return ret;
 }
 
+enum hclge_led_status {
+	HCLGE_LED_OFF,
+	HCLGE_LED_ON,
+	HCLGE_LED_NO_CHANGE = 0xFF,
+};
+
 static int hclge_set_led_id(struct hnae3_handle *handle,
 			    enum ethtool_phys_id_state status)
 {
@@ -5880,27 +5914,52 @@ static int hclge_set_led_id(struct hnae3_handle *handle,
 	struct phy_device *phydev = hdev->hw.mac.phydev;
 	int ret = 0;
 
-	if (!phydev)
-		return -EOPNOTSUPP;
-
-	switch (status) {
-	case ETHTOOL_ID_ACTIVE:
-		ret = hclge_get_led_status_phy(phydev, &hdev->phy_led_val);
-		if (ret)
-			return ret;
-		return BLINK_FREQUENCY;
-	case ETHTOOL_ID_ON:
-		ret = hclge_set_led_status_phy(phydev, HCLGE_LED_FORCE_ON);
-		break;
-	case ETHTOOL_ID_OFF:
-		ret = hclge_set_led_status_phy(phydev, HCLGE_LED_FORCE_OFF);
-		break;
-	case ETHTOOL_ID_INACTIVE:
-		ret = hclge_set_led_status_phy(phydev, hdev->phy_led_val);
-		break;
-	default:
-		ret = -EINVAL;
-		break;
+	if (phydev) {
+		switch (status) {
+		case ETHTOOL_ID_ACTIVE:
+			ret = hclge_get_led_status_phy(phydev,
+						       &hdev->phy_led_val);
+			if (ret)
+				return ret;
+			return BLINK_FREQUENCY;
+		case ETHTOOL_ID_ON:
+			ret = hclge_set_led_status_phy(phydev,
+						       HCLGE_LED_FORCE_ON);
+			break;
+		case ETHTOOL_ID_OFF:
+			ret = hclge_set_led_status_phy(phydev,
+						       HCLGE_LED_FORCE_OFF);
+			break;
+		case ETHTOOL_ID_INACTIVE:
+			ret = hclge_set_led_status_phy(phydev,
+						       hdev->phy_led_val);
+			break;
+		default:
+			ret = -EINVAL;
+			break;
+		}
+	} else if (hdev->hw.mac.media_type == HNAE3_MEDIA_TYPE_FIBER) {
+		switch (status) {
+		case ETHTOOL_ID_ACTIVE:
+			ret = hclge_set_led_status_sfp(hdev,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_ON);
+			break;
+		case ETHTOOL_ID_INACTIVE:
+			ret = hclge_set_led_status_sfp(hdev,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_NO_CHANGE,
+						       HCLGE_LED_OFF);
+			break;
+		default:
+			ret = -EINVAL;
+			break;
+		}
+	} else {
+		ret = -EOPNOTSUPP;
 	}
 
 	return ret;
-- 
2.9.3