çå: çå: çå: [PATCH v6] mfd: Add support for RTS5250S power saving

[åé]

> On Wed, Dec 27, 2017 at 05:37:50PM -0600, Bjorn Helgaas wrote:
> > On Tue, Dec 19, 2017 at 08:15:24AM +0000, åé wrote:
> > > > On Fri, Dec 15, 2017 at 09:42:45AM +0000, åé wrote:
> > > > > > [+cc Hans, Dave, linux-pci]
> > > > > >
> > > > > > On Thu, Sep 07, 2017 at 04:26:39PM +0800,
> > > > > > rui_feng@xxxxxxxxxxxxxx
> > > > wrote:
> > > > > > > From: Rui Feng <rui_feng@xxxxxxxxxxxxxx>
> > > > > >
> > > > > > I wish this had been posted to linux-pci before being merged.
> > > > > >
> > > > > > I'm concerned because some of this appears to overlap and
> > > > > > conflict with PCI core management of ASPM.
> > > > > >
> > > > > > I assume these devices advertise ASPM support in their Link
> > > > > > Capabilites registers, right?  If so, why isn't the existing
> > > > > > PCI core ASPM support sufficient?
> > > > > >
> > > > > When L1SS is configured, the device(hardware) can't enter L1SS
> > > > > status automatically, it need driver(software) to do some work
> > > > > to achieve the
> > > > function.
> > > >
> > > > So this is a hardware defect in the device?  As far as I know,
> > > > ASPM and L1SS are specified such that they should work without special
> driver support.
> > > >
> > > Yes, you can say that.
> > >
> > > > > > > Enable power saving for RTS5250S as following steps:
> > > > > > > 1.Set 0xFE58 to enable clock power management.
> > > > > >
> > > > > > Is this clock power management something specific to RTS5250S,
> > > > > > or is it standard PCIe architected stuff?
> > > > > >
> > > > > 0xFE58 is specific register to RTS5250S not standard PCIe architected
> stuff.
> > > >
> > > > OK.  I asked because devices often mirror architected PCIe config
> > > > things in device-specific MMIO space, and if I squint just right,
> > > > I can sort of match up the register bits you used with things in the PCIe
> spec.
> > > >
> > > > > > > 2.Check cfg space whether support L1SS or not.
> > > > > >
> > > > > > This sounds like standard PCIe ASPM L1 Substates, right?
> > > > > >
> > > > > Yes.
> > > > >
> > > > > > > 3.If support L1SS, set 0xFF03 to free clkreq.
> > > > > > > 4.When entering idle status, enable aspm
> > > > > > >   and set parameters for L1SS and LTR.
> > > > > > > 5.Wnen entering run status, disable aspm
> > > > > > >   and set parameters for L1SS and LTR.
> > > > > >
> > > > > > In general, drivers should not configure ASPM, L1SS, and LTR
> > > > > > themselves; the PCI core should do that.
> > > > > >
> > > > > > If a driver needs to tweak ASPM at run-time, it should use
> > > > > > interfaces exported by the PCI core to do so.
> > > > > >
> > > > > Which interface I can use to set ASPM? I use "pci_write_config_byte"
> now.
> > > >
> > > > What do you need to do?  include/linux/pci-aspm.h exports
> > > > pci_disable_link_state(), which is mainly used to avoid ASPM
> > > > states that have hardware errata.
> > > >
> > > I want to enable ASPM(L0 -> L1) and disable ASPM(L1 -> L0), which
> > > interface can I use?
> >
> > You can use pci_disable_link_state() to disable usage of L1.
> >
> > Currently there is no corresponding pci_enable_link_state().  What if
> > we added something like the following (untested)?  Would that work for
> > you?
> 
> Hi Rui,
> 
> Any thoughts on the patch below?

I'm busy with other work, the patch seems ok, I will test it later.
> 
> > commit 209930d809fa602b8aafdd171b26719cee6c6649
> > Author: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> > Date:   Wed Dec 27 16:56:26 2017 -0600
> >
> >     PCI/ASPM: Add pci_enable_link_state()
> >
> >     Some drivers want control over the ASPM states their device is allowed
> to
> >     use.  We already have a pci_disable_link_state(), and drivers can use
> that
> >     to prevent the device from entering L0 or L1s.
> >
> >     Add a corresponding pci_enable_link_state() so a driver can enable use
> of
> >     L0 or L1s again.
> >
> > diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index
> > 3b9b4d50cd98..ca217195f800 100644
> > --- a/drivers/pci/pcie/aspm.c
> > +++ b/drivers/pci/pcie/aspm.c
> > @@ -1028,6 +1028,67 @@ void pcie_aspm_powersave_config_link(struct
> pci_dev *pdev)
> >  	up_read(&pci_bus_sem);
> >  }
> >
> > +/**
> > + * pci_enable_link_state - Enable device's link state, so the link
> > +may
> > + * enter specific states.  Note that if the BIOS didn't grant ASPM
> > + * control to the OS, this does nothing because we can't touch the
> > +LNKCTL
> > + * register.
> > + *
> > + * @pdev: PCI device
> > + * @state: ASPM link state to enable
> > + */
> > +void pci_enable_link_state(struct pci_dev *pdev, int state) {
> > +	struct pci_dev *parent = pdev->bus->self;
> > +	struct pcie_link_state *link;
> > +	u32 lnkcap;
> > +
> > +	if (!pci_is_pcie(pdev))
> > +		return;
> > +
> > +	if (pdev->has_secondary_link)
> > +		parent = pdev;
> > +	if (!parent || !parent->link_state)
> > +		return;
> > +
> > +	/*
> > +	 * A driver requested that ASPM be enabled on this device, but
> > +	 * if we don't have permission to manage ASPM (e.g., on ACPI
> > +	 * systems we have to observe the FADT ACPI_FADT_NO_ASPM bit and
> > +	 * the _OSC method), we can't honor that request.  Windows has
> > +	 * a similar mechanism using "PciASPMOptOut", which is also
> > +	 * ignored in this situation.
> > +	 */
> > +	if (aspm_disabled) {
> > +		dev_warn(&pdev->dev, "can't enable ASPM; OS doesn't have ASPM
> control\n");
> > +		return;
> > +	}
> > +
> > +	down_read(&pci_bus_sem);
> > +	mutex_lock(&aspm_lock);
> > +	link = parent->link_state;
> > +	if (state & PCIE_LINK_STATE_L0S)
> > +		link->aspm_disable &= ~ASPM_STATE_L0S;
> > +	if (state & PCIE_LINK_STATE_L1)
> > +		link->aspm_disable &= ~ASPM_STATE_L1;
> > +	pcie_config_aspm_link(link, policy_to_aspm_state(link));
> > +
> > +	/*
> > +	 * Enable Clock Power Management if requested by the driver,
> > +	 * supported by the device, and allowed by the current policy.
> > +	 */
> > +	if (state & PCIE_LINK_STATE_CLKPM) {
> > +		pcie_capability_read_dword(pdev, PCI_EXP_LNKCAP, &lnkcap);
> > +		if (lnkcap & PCI_EXP_LNKCAP_CLKPM) {
> > +			link->clkpm_capable = 1;
> > +			pcie_set_clkpm(link, policy_to_clkpm_state(link));
> > +		}
> > +	}
> > +	mutex_unlock(&aspm_lock);
> > +	up_read(&pci_bus_sem);
> > +}
> > +EXPORT_SYMBOL(pci_enable_link_state);
> > +
> >  static void __pci_disable_link_state(struct pci_dev *pdev, int state,
> > bool sem)  {
> >  	struct pci_dev *parent = pdev->bus->self; diff --git
> > a/include/linux/pci-aspm.h b/include/linux/pci-aspm.h index
> > df28af5cef21..cd0736b384ae 100644
> > --- a/include/linux/pci-aspm.h
> > +++ b/include/linux/pci-aspm.h
> > @@ -24,10 +24,12 @@
> >  #define PCIE_LINK_STATE_CLKPM	4
> >
> >  #ifdef CONFIG_PCIEASPM
> > +void pci_enable_link_state(struct pci_dev *pdev, int state);
> >  void pci_disable_link_state(struct pci_dev *pdev, int state);  void
> > pci_disable_link_state_locked(struct pci_dev *pdev, int state);  void
> > pcie_no_aspm(void);  #else
> > +static inline void pci_enable_link_state(struct pci_dev *pdev, int
> > +state) { }
> >  static inline void pci_disable_link_state(struct pci_dev *pdev, int
> > state) { }  static inline void pcie_no_aspm(void) { }  #endif
> 
> ------Please consider the environment before printing this e-mail.