[PATCH v4 1/2] irqchip: add support for Layerscape external interrupt lines

From: Rasmus Villemoes
Date: Thu Jan 25 2018 - 10:02:51 EST


The LS1021A allows inverting the polarity of six interrupt lines
IRQ[0:5] via the scfg_intpcr register, effectively allowing
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING for those. We just need to
check the type, set the relevant bit in INTPCR accordingly, and fixup
the type argument before calling the GIC's irq_set_type.

In fact, the power-on-reset value of the INTPCR register on the LS1021A
is so that all six lines have their polarity inverted. Hence any
hardware connected to those lines is unusable without this: If the line
is indeed active low, the generic GIC code will reject an irq spec with
IRQ_TYPE_LEVEL_LOW, while if the line is active high, we must obviously
disable the polarity inversion (writing 0 to the relevant bit) before
unmasking the interrupt.

Some other Layerscape SOCs (LS1043A, LS1046A) reportedly have a similar
feature, just with a different number of external interrupt lines (and a
different POR value for the INTPCR register). This driver should be
prepared for supporting those by properly filling out the device tree
node, but I don't have the full reference manual, nor the hardware to be
able to test it. I do know, from a tiny clipout from one of the other
reference manuals I was shown, that 1U<<n is the right formula to
use for setting/clearing the bit corresponding to the external IRQn, but
I don't know which interrupts on the GIC those lines represent.

There's also a little Kconfig/Kbuild issue: For now, I've let the driver
be built if CONFIG_SOC_LS1021A is set. For the others, it might make
sense to instead use CONFIG_ARCH_LAYERSCAPE, but SOC_LS1021A does not
select ARCH_LAYERSCAPE. The simplest solution is probably to do what is
done for irq-ls-scfg-msi.c: introduce a "def_bool y if SOC_LS1021A ||
ARCH_LAYERSCAPE" symbol. But I think that can wait until somebody with
the hardware actually tests that this works for the other platforms. At
that point, one can also add the extra IRQCHIP_DECLARE instances.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@xxxxxxxxx>
---
Changes since v2 (all addressing comments from Rob Herring):

- use fsl,bit-reverse rather than bit-reverse
- make the dts node a child of the scfg node
- make the node name "interrupt-controller"

Changes since v3: None

drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-ls-extirq.c | 173 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 174 insertions(+)
create mode 100644 drivers/irqchip/irq-ls-extirq.c

diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index b842dfdc903f..32d7160680fe 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -75,6 +75,7 @@ obj-$(CONFIG_MVEBU_ICU) += irq-mvebu-icu.o
obj-$(CONFIG_MVEBU_ODMI) += irq-mvebu-odmi.o
obj-$(CONFIG_MVEBU_PIC) += irq-mvebu-pic.o
obj-$(CONFIG_LS_SCFG_MSI) += irq-ls-scfg-msi.o
+obj-$(CONFIG_SOC_LS1021A) += irq-ls-extirq.o
obj-$(CONFIG_EZNPS_GIC) += irq-eznps.o
obj-$(CONFIG_ARCH_ASPEED) += irq-aspeed-vic.o irq-aspeed-i2c-ic.o
obj-$(CONFIG_STM32_EXTI) += irq-stm32-exti.o
diff --git a/drivers/irqchip/irq-ls-extirq.c b/drivers/irqchip/irq-ls-extirq.c
new file mode 100644
index 000000000000..ac84ad053b51
--- /dev/null
+++ b/drivers/irqchip/irq-ls-extirq.c
@@ -0,0 +1,173 @@
+#define pr_fmt(fmt) "irq-ls-extirq: " fmt
+
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#define MAXIRQ 12
+
+struct extirq_chip_data {
+ struct regmap *syscon;
+ u32 intpcr;
+ bool bit_reverse;
+ u32 nirq;
+ u32 parent_irq[MAXIRQ];
+};
+
+static int
+ls_extirq_set_type(struct irq_data *data, unsigned int type)
+{
+ irq_hw_number_t hwirq = data->hwirq;
+ struct extirq_chip_data *chip_data = data->chip_data;
+ u32 value, mask;
+
+ if (chip_data->bit_reverse)
+ mask = 1U << (31 - hwirq);
+ else
+ mask = 1U << hwirq;
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_LOW:
+ type = IRQ_TYPE_LEVEL_HIGH;
+ value = mask;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ type = IRQ_TYPE_EDGE_RISING;
+ value = mask;
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ case IRQ_TYPE_EDGE_RISING:
+ value = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_update_bits(chip_data->syscon, chip_data->intpcr, mask, value);
+
+ data = data->parent_data;
+ return data->chip->irq_set_type(data, type);
+}
+
+static struct irq_chip extirq_chip = {
+ .name = "extirq",
+ .irq_mask = irq_chip_mask_parent,
+ .irq_unmask = irq_chip_unmask_parent,
+ .irq_eoi = irq_chip_eoi_parent,
+ .irq_set_type = ls_extirq_set_type,
+ .irq_retrigger = irq_chip_retrigger_hierarchy,
+ .irq_set_affinity = irq_chip_set_affinity_parent,
+ .flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
+static int
+ls_extirq_domain_translate(struct irq_domain *d, struct irq_fwspec *fwspec,
+ unsigned long *hwirq, unsigned int *type)
+{
+ if (!is_of_node(fwspec->fwnode))
+ return -EINVAL;
+
+ if (fwspec->param_count != 3)
+ return -EINVAL;
+
+ /* No PPI should point to this domain */
+ if (fwspec->param[0] != GIC_SPI)
+ return -EINVAL;
+
+ *hwirq = fwspec->param[1];
+ *type = fwspec->param[2] & IRQ_TYPE_SENSE_MASK;
+ return 0;
+}
+
+static int
+ls_extirq_domain_alloc(struct irq_domain *domain, unsigned int virq,
+ unsigned int nr_irqs, void *arg)
+{
+ irq_hw_number_t hwirq;
+ struct irq_fwspec *fwspec = arg;
+ struct irq_fwspec gic_fwspec;
+ struct extirq_chip_data *chip_data = domain->host_data;
+
+ if (fwspec->param_count != 3)
+ return -EINVAL;
+
+ if (fwspec->param[0] != GIC_SPI)
+ return -EINVAL;
+
+ hwirq = fwspec->param[1];
+ if (hwirq >= chip_data->nirq)
+ return -EINVAL;
+
+ irq_domain_set_hwirq_and_chip(domain, virq, hwirq, &extirq_chip,
+ chip_data);
+
+ gic_fwspec.fwnode = domain->parent->fwnode;
+ gic_fwspec.param_count = 3;
+ gic_fwspec.param[0] = GIC_SPI;
+ gic_fwspec.param[1] = chip_data->parent_irq[hwirq];
+ gic_fwspec.param[2] = fwspec->param[2];
+
+ return irq_domain_alloc_irqs_parent(domain, virq, 1, &gic_fwspec);
+}
+
+static const struct irq_domain_ops extirq_domain_ops = {
+ .translate = ls_extirq_domain_translate,
+ .alloc = ls_extirq_domain_alloc,
+ .free = irq_domain_free_irqs_common,
+};
+
+static int __init
+ls_extirq_of_init(struct device_node *node, struct device_node *parent)
+{
+
+ struct irq_domain *domain, *domain_parent;
+ struct extirq_chip_data *chip_data;
+ int ret;
+
+ domain_parent = irq_find_host(parent);
+ if (!domain_parent) {
+ pr_err("interrupt-parent not found\n");
+ return -EINVAL;
+ }
+
+ chip_data = kzalloc(sizeof(*chip_data), GFP_KERNEL);
+ if (!chip_data)
+ return -ENOMEM;
+
+ chip_data->syscon = syscon_node_to_regmap(node->parent);
+ ret = of_property_read_u32(node, "offset", &chip_data->intpcr);
+
+ if (IS_ERR(chip_data->syscon))
+ ret = PTR_ERR(chip_data->syscon);
+ if (ret)
+ goto out_free_chip;
+
+ ret = of_property_read_variable_u32_array(node, "interrupts", chip_data->parent_irq,
+ 1, ARRAY_SIZE(chip_data->parent_irq));
+ if (ret < 0)
+ goto out_free_chip;
+ chip_data->nirq = ret;
+ chip_data->bit_reverse = of_property_read_bool(node, "fsl,bit-reverse");
+
+ domain = irq_domain_add_hierarchy(domain_parent, 0, chip_data->nirq, node,
+ &extirq_domain_ops, chip_data);
+ if (!domain) {
+ ret = -ENOMEM;
+ goto out_free_chip;
+ }
+
+ return 0;
+
+out_free_chip:
+ kfree(chip_data);
+ return ret;
+}
+
+IRQCHIP_DECLARE(ls1021a_extirq, "fsl,ls1021a-extirq", ls_extirq_of_init);
--
2.15.1