Re: [v3] ARM: dts: imx: Add support for Advantech DMS-BA16

From: Yung-Ching LIN
Date: Thu Feb 08 2018 - 14:24:59 EST

Hi Shawn,

Thanks for pointing out the issues.
Please see my inline comments below.

On Thu, Feb 8, 2018 at 1:03 AM, Shawn Guo <shawnguo@xxxxxxxxxx> wrote:
> On Wed, Feb 07, 2018 at 03:17:04AM +0800, Ken Lin wrote:
>> Add support for Advantech DMS-BA16 board, which uses
>> the Advantech BA-16 module.
>>
>> Signed-off-by: Ken Lin <yungching0725@xxxxxxxxx>
>> ---
>> Changes in v3:
>> - Fix the SPDX lines issue
>> - Fix the eeprom setting issue
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/imx6q-dms-ba16.dts | 140 +++++++++++++++++++++++++++++++++++
>> 2 files changed, 141 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..585c3da4a47a 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>> imx6q-dfi-fs700-m60.dtb \
>> imx6q-display5-tianma-tm070-1280x768.dtb \
>> imx6q-dmo-edmqmx6.dtb \
>> + imx6q-dms-ba16.dtb \
>> imx6q-evi.dtb \
>> imx6q-gk802.dtb \
>> imx6q-gw51xx.dtb \
>> diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
>> new file mode 100644
>> index 000000000000..b5047fd88290
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
>> @@ -0,0 +1,140 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include "imx6q-ba16.dtsi"
>> +
>> +/ {
>> + model = "Advantech DMS-BA16";
>> + compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
>> +
>> + reg_usb_otg_vbus: regulator-usbotgvbus {
>> + compatible = "regulator-fixed";
>> + regulator-name = "usb_otg_vbus";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbotgvbus>;
>> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +
>> + sys_mclk: clock-sys-mclk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <22000000>;
>> + };
>> +
>> + sound {
>> + compatible = "fsl,imx6q-ba16-sgtl5000",
>> + "fsl,imx-audio-sgtl5000";
>> + model = "imx6q-ba16-sgtl5000";
>> + ssi-controller = <&ssi1>;
>> + audio-codec = <&sgtl5000>;
>> + audio-routing =
>> + "MIC_IN", "Mic Jack",
>> + "Mic Jack", "Mic Bias",
>> + "Headphone Jack", "HP_OUT";
>> + mux-int-port = <1>;
>> + mux-ext-port = <4>;
>> + };
>> +};
>> +
>> +&ecspi5 {
>> + cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ecspi5>;
>> + status = "okay";
>> +
>> + m25_eeprom: m25p80@0 {
>> + compatible = "atmel,at25256B", "atmel,at25";
>> + spi-max-frequency = <20000000>;
>> + size = <0x8000>;
>> + pagesize = <64>;
>> + reg = <0>;
>> + address-width = <16>;
>> + };
>> +};
>> +
>> +&iomuxc {
>> +
>
> Unnecessary newline.
>


Thanks. Will fix this in the v4.

>> + pinctrl_usbotgvbus: usbotgvbusgrp {
>
> Please keep the pinctrl entries under iomuxc node alphabetically sorted.
>

Thanks. Will fix this in the v4.

>> + fsl,pins = <
>> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
>> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
>
> MX6QDL_PAD_GPIO_1__USB_OTG_ID shouldn't belong to this group but
> pinctrl_usbotg. However that has been defined in imx6q-ba16.dtsi using
> another USB_OTG_ID pinmux. Confusing.
>
> Shawn

Will correct the USB_OTG_ID pinmux setting in the v4.
Do you mind if I redefine reg_usb_otg_vbus node since we just started
using OTG host/device mode on this board ?

>
>> + >;
>> + };
>> +
>> + pinctrl_i2c1_gpio: i2c1gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
>> + MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
>> + >;
>> + };
>> +
>> + pinctrl_i2c2_gpio: i2c2gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
>> + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
>> + >;
>> + };
>> +
>> + pinctrl_i2c3_gpio: i2c3gpiogrp {
>> + fsl,pins = <
>> + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
>> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
>> + >;
>> + };
>> +};
>> +
>> +&i2c1 {
>> + clock-frequency = <100000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_i2c1>;
>> + status = "okay";
>> +
>> + sgtl5000: codec@a {
>> + compatible = "fsl,sgtl5000";
>> + reg = <0x0a>;
>> + clocks = <&sys_mclk>;
>> + lrclk-strength = <0x3>;
>> + VDDA-supply = <&reg_1p8v>;
>> + VDDIO-supply = <&reg_3p3v>;
>> + };
>> +};
>> +
>> +&pwm2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_pwm2>;
>> + status = "okay";
>> +};
>> +
>> +&sata {
>> + fsl,no-spread-spectrum;
>> + fsl,transmit-atten-16ths = <12>;
>> + fsl,transmit-boost-mdB = <3330>;
>> + fsl,transmit-level-mV = <1133>;
>> + fsl,receive-dpll-mode = <1>;
>> + status = "okay";
>> +};
>> +
>> +&usbotg {
>> + vbus-supply = <&reg_usb_otg_vbus>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usbotg>;
>> + dr_mode = "otg";
>> + disable-over-current;
>> + status = "okay";
>> +};
>> +
>> +&usdhc4 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usdhc4>;
>> + bus-width = <8>;
>> + cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
>> + no-1-8-v;
>> + keep-power-in-suspend;
>> + wakeup-source;
>> + status = "okay";
>> +};
>> --
>> 2.11.0
>>