Re: [PATCH] clk: tegra: fix pllu rate configuration
From: Peter De Schrijver
Date: Thu Mar 01 2018 - 02:41:42 EST
On Wed, Feb 28, 2018 at 08:20:47PM +0300, Dmitry Osipenko wrote:
> On 28.02.2018 17:14, Peter De Schrijver wrote:
> > On Wed, Feb 28, 2018 at 03:00:23PM +0300, Dmitry Osipenko wrote:
> >> On 28.02.2018 12:36, Peter De Schrijver wrote:
> >>> On Tue, Feb 27, 2018 at 02:59:11PM +0300, Dmitry Osipenko wrote:
> >>>> On 27.02.2018 02:04, Marcel Ziswiler wrote:
> >>>>> On Mon, 2018-02-26 at 15:42 +0300, Dmitry Osipenko wrote:
> >>>>>> On 23.02.2018 02:04, Marcel Ziswiler wrote:
> >>>>>>> Turns out latest upstream U-Boot does not configure/enable pllu
> >>>>>>> which
> >>>>>>> leaves it at some default rate of 500 kHz:
> >>>>>>>
> >>>>>>> root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep
> >>>>>>> pll_u
> >>>>>>> pll_u 3 3 0 500000
> >>>>>>> 0
> >>>>>>>
> >>>>>>> Of course this won't quite work leading to the following messages:
> >>>>>>>
> >>>>>>> [ 6.559593] usb 2-1: new full-speed USB device number 2 using
> >>>>>>> tegra-
> >>>>>>> ehci
> >>>>>>> [ 11.759173] usb 2-1: device descriptor read/64, error -110
> >>>>>>> [ 27.119453] usb 2-1: device descriptor read/64, error -110
> >>>>>>> [ 27.389217] usb 2-1: new full-speed USB device number 3 using
> >>>>>>> tegra-
> >>>>>>> ehci
> >>>>>>> [ 32.559454] usb 2-1: device descriptor read/64, error -110
> >>>>>>> [ 47.929777] usb 2-1: device descriptor read/64, error -110
> >>>>>>> [ 48.049658] usb usb2-port1: attempt power cycle
> >>>>>>> [ 48.759475] usb 2-1: new full-speed USB device number 4 using
> >>>>>>> tegra-
> >>>>>>> ehci
> >>>>>>> [ 59.349457] usb 2-1: device not accepting address 4, error -110
> >>>>>>> [ 59.509449] usb 2-1: new full-speed USB device number 5 using
> >>>>>>> tegra-
> >>>>>>> ehci
> >>>>>>> [ 70.069457] usb 2-1: device not accepting address 5, error -110
> >>>>>>> [ 70.079721] usb usb2-port1: unable to enumerate USB device
> >>>>>>>
> >>>>>>> Fix this by actually allowing the rate also being set from within
> >>>>>>> the Linux kernel.
> >>>
> >>> I think the best solution to this problem would be to make pll_u a fixed
> >>> clock and enable it and program the rate if it's not enabled at boot.
> >>
> >> Oh, right. PLL_U rate is actually configurable, somehow I missed it in TRM
> >> yesterday.. So set/round_rate() for PLL_U are actually needed and the patch is
> >> correct. Seems only T20 misses PLL_U in the init table, probably worth to add it
> >> there.
> >>
> >
> > AFAIK we only use one rate ever?
>
> IIUC, PLL_U has 3 outputs and output dividers are fixed in HW. So yes, we are
> setting PLL_U to one rate - 480MHz to get out1-480MHz, out2-60MHz and out3-12MHz.
>
Indeed. And given that it's hw controlled anyway, I don't see why we can't make
it a fixed clock and handle the init at kernel boot depending on what the
bootloader has done.
Peter.