Re: [PATCH v2 1/2] dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)

From: Kishon Vijay Abraham I
Date: Fri Mar 02 2018 - 01:03:34 EST




On Thursday 01 March 2018 09:00 PM, Amelie Delaunay wrote:
> This patch adds the device tree bindings description for STM32 USBPHYC
> (USB PHY Controller).
>
> Signed-off-by: Amelie Delaunay <amelie.delaunay@xxxxxx>
> ---
> .../devicetree/bindings/phy/phy-stm32-usbphyc.txt | 46 ++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt
> new file mode 100644
> index 0000000..1ad3893
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.txt
> @@ -0,0 +1,46 @@
> +STMicroelectronics STM32 USB HS PHY controller
> +
> +The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
> +switch. It controls PHY configuration and status, and the UTMI+ switch that
> +selects either OTG or HOST controller for the second PHY port. It also sets
> +PLL configuration.
> +
> +USBPHYC
> + |_ PLL
> + |
> + |_ PHY port#1 _________________ HOST controller
> + | _ |
> + | / 1|________________|
> + |_ PHY port#2 ----| |________________
> + | \_0| |
> + |_ UTMI switch_______| OTG controller
> +
> +

This should be modeled as a phy provider node with two separate sub-nodes for
each of the PHYs.

Thanks
Kishon

> +Required properties:
> +- compatible: must be "st,stm32mp1-usbphyc"
> +- reg: address and length of the usb phy control register set
> +- clocks: phandle + clock specifier for the PLL phy clock
> +- phy-supply: from the generic phy bindings, phandle to the regulator
> + providing 3V3 power to the PHY, see phy-bindings.txt
> +- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
> +- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
> +
> +Optional properties:
> +- assigned-clocks: phandle + clock specifier for the PLL phy clock
> +- assigned-clock-parents: the PLL phy clock parent
> +- resets: phandle + reset specifier
> +- st,utmi-switch: should be <0> or <1>, to select USB controller for PHY
> + port#2. If not specified, 0 is the default selection.
> +
> +
> +Example:
> + usbphyc: usb-phy@5a006000 {
> + compatible = "st,stm32mp1-usbphyc";
> + reg = <0x5a006000 0x1000>;
> + clocks = <&rcc_clk USBPHY_K>;
> + resets = <&rcc_rst USBPHY_R>;
> + st,utmi-switch = <1>;
> + phy-supply = <&vdd_usb>;
> + vdda1v1-supply = <&reg11>;
> + vdda1v8-supply = <&reg18>
> + };
>