Re: [PATCH] clk: tegra: fix pllu rate configuration

[Jon Hunter]

On 01/03/18 07:41, Peter De Schrijver wrote:
> On Wed, Feb 28, 2018 at 08:20:47PM +0300, Dmitry Osipenko wrote:
>> On 28.02.2018 17:14, Peter De Schrijver wrote:
>>> On Wed, Feb 28, 2018 at 03:00:23PM +0300, Dmitry Osipenko wrote:
>>>> On 28.02.2018 12:36, Peter De Schrijver wrote:
>>>>> On Tue, Feb 27, 2018 at 02:59:11PM +0300, Dmitry Osipenko wrote:
>>>>>> On 27.02.2018 02:04, Marcel Ziswiler wrote:
>>>>>>> On Mon, 2018-02-26 at 15:42 +0300, Dmitry Osipenko wrote:
>>>>>>>> On 23.02.2018 02:04, Marcel Ziswiler wrote:
>>>>>>>>> Turns out latest upstream U-Boot does not configure/enable pllu
>>>>>>>>> which
>>>>>>>>> leaves it at some default rate of 500 kHz:
>>>>>>>>>
>>>>>>>>> root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep
>>>>>>>>> pll_u
>>>>>>>>>        pll_u                  3        3        0      500000      
>>>>>>>>>     0
>>>>>>>>>
>>>>>>>>> Of course this won't quite work leading to the following messages:
>>>>>>>>>
>>>>>>>>> [    6.559593] usb 2-1: new full-speed USB device number 2 using
>>>>>>>>> tegra-
>>>>>>>>> ehci
>>>>>>>>> [   11.759173] usb 2-1: device descriptor read/64, error -110
>>>>>>>>> [   27.119453] usb 2-1: device descriptor read/64, error -110
>>>>>>>>> [   27.389217] usb 2-1: new full-speed USB device number 3 using
>>>>>>>>> tegra-
>>>>>>>>> ehci
>>>>>>>>> [   32.559454] usb 2-1: device descriptor read/64, error -110
>>>>>>>>> [   47.929777] usb 2-1: device descriptor read/64, error -110
>>>>>>>>> [   48.049658] usb usb2-port1: attempt power cycle
>>>>>>>>> [   48.759475] usb 2-1: new full-speed USB device number 4 using
>>>>>>>>> tegra-
>>>>>>>>> ehci
>>>>>>>>> [   59.349457] usb 2-1: device not accepting address 4, error -110
>>>>>>>>> [   59.509449] usb 2-1: new full-speed USB device number 5 using
>>>>>>>>> tegra-
>>>>>>>>> ehci
>>>>>>>>> [   70.069457] usb 2-1: device not accepting address 5, error -110
>>>>>>>>> [   70.079721] usb usb2-port1: unable to enumerate USB device
>>>>>>>>>
>>>>>>>>> Fix this by actually allowing the rate also being set from within
>>>>>>>>> the Linux kernel.
>>>>>
>>>>> I think the best solution to this problem would be to make pll_u a fixed
>>>>> clock and enable it and program the rate if it's not enabled at boot.
>>>>
>>>> Oh, right. PLL_U rate is actually configurable, somehow I missed it in TRM
>>>> yesterday.. So set/round_rate() for PLL_U are actually needed and the patch is
>>>> correct. Seems only T20 misses PLL_U in the init table, probably worth to add it
>>>> there.
>>>>
>>>
>>> AFAIK we only use one rate ever?
>>
>> IIUC, PLL_U has 3 outputs and output dividers are fixed in HW. So yes, we are
>> setting PLL_U to one rate - 480MHz to get out1-480MHz, out2-60MHz and out3-12MHz.
>>
> 
> Indeed. And given that it's hw controlled anyway, I don't see why we can't make
> it a fixed clock and handle the init at kernel boot depending on what the
> bootloader has done.

Peter, are you suggesting we implement the equivalent to
tegra210_init_pllu()? This does look a bit more involved that what this
change is doing. Is there a simple way to do what you are suggesting?

Cheers
Jon

-- 
nvpublic