Re: [PATCH v2 1/4] dt-bindings: mfd: Add Gateworks System Controller bindings

[Rob Herring]

On Mon, Mar 05, 2018 at 02:02:38PM -0800, Tim Harvey wrote:
> This patch adds documentation of device-tree bindings for the
> Gateworks System Controller (GSC).
> 
> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/mfd/gsc.txt | 159 ++++++++++++++++++++++++++
>  1 file changed, 159 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/gsc.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/gsc.txt b/Documentation/devicetree/bindings/mfd/gsc.txt
> new file mode 100644
> index 0000000..fe5d114
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/gsc.txt
> @@ -0,0 +1,159 @@
> +Gateworks System Controller multi-function device
> +
> +The GSC is a Multifunction I2C slave device with the following submodules:
> +- WDT
> +- GPIO
> +- Pushbutton controller
> +- HWMON
> +
> +Required properties:
> +- compatible : Must be "gw,gsc_v1", "gw,gsc_v2", "gw,gsc_v3"

s/_/-/

> +- reg: I2C address of the device
> +- interrupts: interrupt triggered by GSC_IRQ# signal
> +- interrupt-parent: Interrupt controller GSC is connected to
> +- #interrupt-cells: should be <1>, index of the interrupt within the
> +  controller, in accordance with the "one cell" variant of
> +  <devicetree/bindings/interrupt-controller/interrupt.txt>
> +
> +Optional nodes:
> +* watchdog:
> +The GSC provides a Watchdog monitor which can power cycle the board's
> +primary power supply on most board models when tripped.
> +
> +Required properties:
> +- compatible: must be "gw,gsc-watchdog"
> +
> +* input:
> +The GSC provides an input device capable of dispatching Linux Input events

Linux details that are not relevant to the binding.

> +for user pushbutton events, tamper switch events, etc.
> +
> +Required properties:
> +- compatible: must be "gw,gsc-input"
> +
> +* hwmon:
> +The GSC provides a set of Analog to Digitcal Converter (ADC) pins used for
> +temperature and/or voltage monitoring.
> +
> +Required properties:
> +- compatible: must be "gw,gsc-hwmon"
> +
> +Example:
> +
> +	gsc: gsc@20 {
> +		compatible = "gw,gsc_v2";
> +		reg = <0x20>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +
> +		gsc_input {

input {

> +			compatible = "gw,gsc-input";
> +		};
> +
> +		gsc_watchdog {

watchdog {

> +			compatible = "gw,gsc-watchdog";
> +		};
> +
> +		gsc_hwmon {

hwmon {

> +			compatible = "gw,gsc-hwmon";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			hwmon@0 { /* A0: Board Temperature */
> +				type = <0>;

Not documented.

> +				reg = <0x00>;
> +				label = "temp";
> +			};
> +
> +			hwmon@1 { /* A1: Input Voltage */
> +				type = <1>;
> +				reg = <0x02>;
> +				label = "Vin";
> +			};
> +
> +			hwmon@2 { /* A2: 5P0 */
> +				type = <1>;
> +				reg = <0x0b>;
> +				label = "5P0";
> +			};
> +
> +			hwmon@4 { /* A4: 0-5V input */
> +				type = <1>;
> +				reg = <0x14>;
> +				label = "ANL0";
> +			};
> +
> +			hwmon@5 { /* A5: 2P5 PCIe/GigE */
> +				type = <1>;
> +				reg = <0x23>;
> +				label = "2P5";
> +			};
> +
> +			hwmon@6 { /* A6: 1P8 Aud/Vid */
> +				type = <1>;
> +				reg = <0x1d>;
> +				label = "1P8";
> +			};
> +
> +			hwmon@7 { /* A7: GPS */
> +				type = <1>;
> +				reg = <0x26>;
> +				label = "GPS";
> +			};
> +
> +			hwmon@12 { /* A12: VDD_CORE */
> +				type = <1>;
> +				reg = <0x3>;
> +				label = "VDD_CORE";
> +			};
> +
> +			hwmon@13 { /* A13: VDD_SOC */
> +				type = <1>;
> +				reg = <0x11>;
> +				label = "VDD_SOC";
> +			};
> +
> +			hwmon@14 { /* A14: 1P0 PCIe SW */
> +				type = <1>;
> +				reg = <0x20>;
> +				label = "1P0";
> +			};
> +
> +			hwmon@15 { /* fan0 */
> +				type = <2>;
> +				reg = <0x2c>;
> +				label = "fan_50p";
> +			};
> +
> +			hwmon@16 { /* fan1 */
> +				type = <2>;
> +				reg = <0x2e>;
> +				label = "fan_60p";
> +			};
> +
> +			hwmon@17 { /* fan2 */
> +				type = <2>;
> +				reg = <0x30>;
> +				label = "fan_70p";
> +			};
> +
> +			hwmon@18 { /* fan3 */
> +				type = <2>;
> +				reg = <0x32>;
> +				label = "fan_80p";
> +			};
> +
> +			hwmon@19 { /* fan4 */
> +				type = <2>;
> +				reg = <0x34>;
> +				label = "fan_90p";
> +			};
> +
> +			hwmon@20 { /* fan5 */
> +				type = <2>;
> +				reg = <0x36>;
> +				label = "fan_100p";
> +			};
> +		};
> +	};
> -- 
> 2.7.4
>