Re: [PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor support
From: Zhang Rui
Date: Tue Mar 13 2018 - 02:51:21 EST
yeah, will review it and get back to you later.
On ä, 2018-03-13 at 06:13 +0000, Anson Huang wrote:
> Ping...
>
> @rui.zhang@xxxxxxxxx, can you help review this patch?
>
> Anson Huang
> Best Regards!
>
>
> >
> > -----Original Message-----
> > From: linux-arm-kernel [mailto:linux-arm-kernel-bounces@xxxxxxxxxxx
> > dead.org]
> > On Behalf Of Anson Huang
> > Sent: Friday, March 2, 2018 10:00 AM
> > To: Leonard Crestez <leonard.crestez@xxxxxxx>; rui.zhang@xxxxxxxxx;
> > edubezval@xxxxxxxxx; robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx;
> > shawnguo@xxxxxxxxxx; kernel@xxxxxxxxxxxxxx; Fabio Estevam
> > <fabio.estevam@xxxxxxx>; linux@xxxxxxxxxxxxxxx
> > Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxx
> > g;
> > dl-linux-imx <linux-imx@xxxxxxx>; linux-kernel@xxxxxxxxxxxxxxx;
> > linux-pm@xxxxxxxxxxxxxxx
> > Subject: [PATCH V6 2/2] thermal: imx: add i.MX7 thermal sensor
> > support
> >
> > This patch adds i.MX7 thermal sensor support, most of the i.MX7
> > thermal sensor
> > functions are same with
> > i.MX6 except the registers offset/layout, so we move those
> > registers
> > offset/layout definitions to soc data structure.
> >
> > i.MX7 uses single calibration data @25C, the calibration data is
> > located at
> > OCOTP offset 0x4F0, bit[17:9], the formula is as below:
> >
> > Tmeas = (Nmeas - n1) + 25; n1 is the fuse value for 25C.
> >
> > Signed-off-by: Anson Huang <Anson.Huang@xxxxxxx>
> > Signed-off-by: Bai Ping <ping.bai@xxxxxxx>
> > Acked-by: Dong Aisheng <aisheng.dong@xxxxxxx>
> > Acked-by: Shawn Guo <shawnguo@xxxxxxxxxx>
> > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > ---
> > changes since V5:
> > no code change, just add Reviewed-by.
> > Â.../devicetree/bindings/thermal/imx-thermal.txtÂÂÂÂ|ÂÂÂ9 +-
> > Âdrivers/thermal/imx_thermal.cÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ| 295
> > ++++++++++++++++-----
> > Â2 files changed, 239 insertions(+), 65 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/imx-
> > thermal.txt
> > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > index 28be51a..38bffcc 100644
> > --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > @@ -1,8 +1,13 @@
> > Â* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
> >
> > ÂRequired properties:
> > -- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-
> > tempmon" for
> > i.MX6SX.
> > -ÂÂi.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the
> > other is
> > IRQ_PANIC,
> > +- compatible : must be one of following:
> > +ÂÂ- "fsl,imx6q-tempmon" for i.MX6Q,
> > +ÂÂ- "fsl,imx6sx-tempmon" for i.MX6SX,
> > +ÂÂ- "fsl,imx7d-tempmon" for i.MX7S/D.
> > +- interrupts : the interrupt output of the controller:
> > +ÂÂi.MX6Q has one IRQ which will be triggered when temperature is
> > higher
> > +than high threshold,
> > +ÂÂi.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is
> > IRQ_LOW
> > +and the other is IRQ_PANIC,
> > ÂÂÂwhen temperature is below than low threshold, IRQ_LOW will be
> > triggered,
> > when temperature
> > ÂÂÂis higher than panic threshold, system will auto reboot by SRC
> > module.
> > Â- fsl,tempmon : phandle pointer to system controller that contains
> > TEMPMON
> > diff --git a/drivers/thermal/imx_thermal.c
> > b/drivers/thermal/imx_thermal.c
> > index a67781b..569d41b 100644
> > --- a/drivers/thermal/imx_thermal.c
> > +++ b/drivers/thermal/imx_thermal.c
> > @@ -31,35 +31,57 @@
> > Â#define REG_CLR 0x8
> > Â#define REG_TOG 0xc
> >
> > -#define MISC0 0x0150
> > -#define MISC0_REFTOP_SELBIASOFF (1 << 3)
> > -#define MISC1 0x0160
> > -#define MISC1_IRQ_TEMPHIGH (1 << 29)
> > +/* i.MX6 specific */
> > +#define IMX6_MISC0 0x0150
> > +#define IMX6_MISC0_REFTOP_SELBIASOFF (1 << 3)
> > +#define IMX6_MISC1 0x0160
> > +#define IMX6_MISC1_IRQ_TEMPHIGH (1 << 29)
> > Â/* Below LOW and PANIC bits are only for TEMPMON_IMX6SX */
> > -#define MISC1_IRQ_TEMPLOW (1 << 28)
> > -#define MISC1_IRQ_TEMPPANIC (1 << 27)
> > -
> > -#define TEMPSENSE0 0x0180
> > -#define TEMPSENSE0_ALARM_VALUE_SHIFT 20
> > -#define TEMPSENSE0_ALARM_VALUE_MASK (0xfff <<
> > TEMPSENSE0_ALARM_VALUE_SHIFT)
> > -#define TEMPSENSE0_TEMP_CNT_SHIFT 8
> > -#define TEMPSENSE0_TEMP_CNT_MASK (0xfff <<
> > TEMPSENSE0_TEMP_CNT_SHIFT)
> > -#define TEMPSENSE0_FINISHED (1 << 2)
> > -#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
> > -#define TEMPSENSE0_POWER_DOWN (1 << 0)
> > -
> > -#define TEMPSENSE1 0x0190
> > -#define TEMPSENSE1_MEASURE_FREQ 0xffff
> > -/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > -#define TEMPSENSE2 0x0290
> > -#define TEMPSENSE2_LOW_VALUE_SHIFT 0
> > -#define TEMPSENSE2_LOW_VALUE_MASK 0xfff
> > -#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
> > -#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
> > +#define IMX6_MISC1_IRQ_TEMPLOW (1 << 28)
> > +#define IMX6_MISC1_IRQ_TEMPPANIC (1 << 27)
> > +
> > +#define IMX6_TEMPSENSE0 0x0180
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT 20
> > +#define IMX6_TEMPSENSE0_ALARM_VALUE_MASK (0xfff << 20)
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_SHIFT 8
> > +#define IMX6_TEMPSENSE0_TEMP_CNT_MASK (0xfff << 8)
> > +#define IMX6_TEMPSENSE0_FINISHED (1 << 2)
> > +#define IMX6_TEMPSENSE0_MEASURE_TEMP (1 << 1)
> > +#define IMX6_TEMPSENSE0_POWER_DOWN (1 << 0)
> > +
> > +#define IMX6_TEMPSENSE1 0x0190
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ 0xffff
> > +#define IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT 0
> >
> > Â#define OCOTP_MEM0 0x0480
> > Â#define OCOTP_ANA1 0x04e0
> >
> > +/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
> > +#define IMX6_TEMPSENSE2 0x0290
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_SHIFT 0
> > +#define IMX6_TEMPSENSE2_LOW_VALUE_MASK 0xfff
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT 16
> > +#define IMX6_TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
> > +
> > +/* i.MX7 specific */
> > +#define IMX7_ANADIG_DIGPROG 0x800
> > +#define IMX7_TEMPSENSE0 0x300
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT 18
> > +#define IMX7_TEMPSENSE0_PANIC_ALARM_MASK (0x1ff << 18)
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT 9
> > +#define IMX7_TEMPSENSE0_HIGH_ALARM_MASK (0x1ff <<
> > 9)
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_SHIFT 0
> > +#define IMX7_TEMPSENSE0_LOW_ALARM_MASK 0x1ff
> > +
> > +#define IMX7_TEMPSENSE1 0x310
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT 16
> > +#define IMX7_TEMPSENSE1_MEASURE_FREQ_MASK (0xffff << 16)
> > +#define IMX7_TEMPSENSE1_FINISHED (1 << 11)
> > +#define IMX7_TEMPSENSE1_MEASURE_TEMP (1 << 10)
> > +#define IMX7_TEMPSENSE1_POWER_DOWN (1 << 9)
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT 0
> > +#define IMX7_TEMPSENSE1_TEMP_VALUE_MASK 0x1ff
> > +
> > Â/* The driver supports 1 passive trip point and 1 critical trip
> > point */ÂÂenum
> > imx_thermal_trip {
> > Â IMX_TRIP_PASSIVE,
> > @@ -72,17 +94,114 @@ enum imx_thermal_trip {
> >
> > Â#define TEMPMON_IMX6Q 1
> > Â#define TEMPMON_IMX6SX 2
> > +#define TEMPMON_IMX7D 3
> >
> > Âstruct thermal_soc_data {
> > Â u32 version;
> > +
> > + u32 sensor_ctrl;
> > + u32 power_down_mask;
> > + u32 measure_temp_mask;
> > +
> > + u32 measure_freq_ctrl;
> > + u32 measure_freq_mask;
> > + u32 measure_freq_shift;
> > +
> > + u32 temp_data;
> > + u32 temp_value_mask;
> > + u32 temp_value_shift;
> > + u32 temp_valid_mask;
> > +
> > + u32 panic_alarm_ctrl;
> > + u32 panic_alarm_mask;
> > + u32 panic_alarm_shift;
> > +
> > + u32 high_alarm_ctrl;
> > + u32 high_alarm_mask;
> > + u32 high_alarm_shift;
> > +
> > + u32 low_alarm_ctrl;
> > + u32 low_alarm_mask;
> > + u32 low_alarm_shift;
> > Â};
> >
> > Âstatic struct thermal_soc_data thermal_imx6q_data = {
> > Â .version = TEMPMON_IMX6Q,
> > +
> > + .sensor_ctrl = IMX6_TEMPSENSE0,
> > + .power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > + .measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX6_TEMPSENSE1,
> > + .measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > + .temp_data = IMX6_TEMPSENSE0,
> > + .temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > + .temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > + .temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > + .high_alarm_ctrl = IMX6_TEMPSENSE0,
> > + .high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > + .high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > Â};
> >
> > Âstatic struct thermal_soc_data thermal_imx6sx_data = {
> > Â .version = TEMPMON_IMX6SX,
> > +
> > + .sensor_ctrl = IMX6_TEMPSENSE0,
> > + .power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
> > + .measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX6_TEMPSENSE1,
> > + .measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
> > +
> > + .temp_data = IMX6_TEMPSENSE0,
> > + .temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
> > + .temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
> > + .temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
> > +
> > + .high_alarm_ctrl = IMX6_TEMPSENSE0,
> > + .high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
> > + .high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
> > +
> > + .panic_alarm_ctrl = IMX6_TEMPSENSE2,
> > + .panic_alarm_mask = IMX6_TEMPSENSE2_PANIC_VALUE_MASK,
> > + .panic_alarm_shift = IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT,
> > +
> > + .low_alarm_ctrl = IMX6_TEMPSENSE2,
> > + .low_alarm_mask = IMX6_TEMPSENSE2_LOW_VALUE_MASK,
> > + .low_alarm_shift = IMX6_TEMPSENSE2_LOW_VALUE_SHIFT, };
> > +
> > +static struct thermal_soc_data thermal_imx7d_data = {
> > + .version = TEMPMON_IMX7D,
> > +
> > + .sensor_ctrl = IMX7_TEMPSENSE1,
> > + .power_down_mask = IMX7_TEMPSENSE1_POWER_DOWN,
> > + .measure_temp_mask = IMX7_TEMPSENSE1_MEASURE_TEMP,
> > +
> > + .measure_freq_ctrl = IMX7_TEMPSENSE1,
> > + .measure_freq_shift = IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT,
> > + .measure_freq_mask = IMX7_TEMPSENSE1_MEASURE_FREQ_MASK,
> > +
> > + .temp_data = IMX7_TEMPSENSE1,
> > + .temp_value_mask = IMX7_TEMPSENSE1_TEMP_VALUE_MASK,
> > + .temp_value_shift = IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT,
> > + .temp_valid_mask = IMX7_TEMPSENSE1_FINISHED,
> > +
> > + .panic_alarm_ctrl = IMX7_TEMPSENSE1,
> > + .panic_alarm_mask = IMX7_TEMPSENSE0_PANIC_ALARM_MASK,
> > + .panic_alarm_shift = IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT,
> > +
> > + .high_alarm_ctrl = IMX7_TEMPSENSE0,
> > + .high_alarm_mask = IMX7_TEMPSENSE0_HIGH_ALARM_MASK,
> > + .high_alarm_shift = IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT,
> > +
> > + .low_alarm_ctrl = IMX7_TEMPSENSE0,
> > + .low_alarm_mask = IMX7_TEMPSENSE0_LOW_ALARM_MASK,
> > + .low_alarm_shift = IMX7_TEMPSENSE0_LOW_ALARM_SHIFT,
> > Â};
> >
> > Âstruct imx_thermal_data {
> > @@ -107,31 +226,42 @@ struct imx_thermal_data {ÂÂstatic void
> > imx_set_panic_temp(struct imx_thermal_data *data,
> > Â ÂÂÂÂÂÂÂint panic_temp)
> > Â{
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > Â struct regmap *map = data->tempmon;
> > Â int critical_value;
> >
> > Â critical_value = (data->c2 - panic_temp) / data->c1;
> > - regmap_write(map, TEMPSENSE2 + REG_CLR,
> > TEMPSENSE2_PANIC_VALUE_MASK);
> > - regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
> > - TEMPSENSE2_PANIC_VALUE_SHIFT);
> > +
> > + regmap_write(map, soc_data->panic_alarm_ctrl + REG_CLR,
> > + ÂÂÂÂÂsoc_data->panic_alarm_mask);
> > + regmap_write(map, soc_data->panic_alarm_ctrl + REG_SET,
> > + ÂÂÂÂÂcritical_value << soc_data-
> > >panic_alarm_shift);
> > Â}
> >
> > Âstatic void imx_set_alarm_temp(struct imx_thermal_data *data,
> > Â ÂÂÂÂÂÂÂint alarm_temp)
> > Â{
> > Â struct regmap *map = data->tempmon;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > Â int alarm_value;
> >
> > Â data->alarm_temp = alarm_temp;
> > - alarm_value = (data->c2 - alarm_temp) / data->c1;
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_ALARM_VALUE_MASK);
> > - regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
> > - TEMPSENSE0_ALARM_VALUE_SHIFT);
> > +
> > + if (data->socdata->version == TEMPMON_IMX7D)
> > + alarm_value = alarm_temp / 1000 + data->c1 - 25;
> > + else
> > + alarm_value = (data->c2 - alarm_temp) / data->c1;
> > +
> > + regmap_write(map, soc_data->high_alarm_ctrl + REG_CLR,
> > + ÂÂÂÂÂsoc_data->high_alarm_mask);
> > + regmap_write(map, soc_data->high_alarm_ctrl + REG_SET,
> > + ÂÂÂÂÂalarm_value << soc_data->high_alarm_shift);
> > Â}
> >
> > Âstatic int imx_get_temp(struct thermal_zone_device *tz, int
> > *temp)ÂÂ{
> > Â struct imx_thermal_data *data = tz->devdata;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> > Â struct regmap *map = data->tempmon;
> > Â unsigned int n_meas;
> > Â bool wait;
> > @@ -139,16 +269,18 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> >
> > Â if (data->mode == THERMAL_DEVICE_ENABLED) {
> > Â /* Check if a measurement is currently in progress
> > */
> > - regmap_read(map, TEMPSENSE0, &val);
> > - wait = !(val & TEMPSENSE0_FINISHED);
> > + regmap_read(map, soc_data->temp_data, &val);
> > + wait = !(val & soc_data->temp_valid_mask);
> > Â } else {
> > Â /*
> > Â Â* Every time we measure the temperature, we will
> > power on the
> > Â Â* temperature sensor, enable measurements, take a
> > reading,
> > Â Â* disable measurements, power off the temperature
> > sensor.
> > Â Â*/
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂsoc_data->power_down_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + ÂÂÂÂsoc_data->measure_temp_mask);
> >
> > Â wait = true;
> > Â }
> > @@ -160,22 +292,28 @@ static int imx_get_temp(struct
> > thermal_zone_device
> > *tz, int *temp)
> > Â if (wait)
> > Â usleep_range(20, 50);
> >
> > - regmap_read(map, TEMPSENSE0, &val);
> > + regmap_read(map, soc_data->temp_data, &val);
> >
> > Â if (data->mode != THERMAL_DEVICE_ENABLED) {
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂsoc_data->measure_temp_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂsoc_data->power_down_mask);
> > Â }
> >
> > - if ((val & TEMPSENSE0_FINISHED) == 0) {
> > + if ((val & soc_data->temp_valid_mask) == 0) {
> > Â dev_dbg(&tz->device, "temp measurement never
> > finished\n");
> > Â return -EAGAIN;
> > Â }
> >
> > - n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >>
> > TEMPSENSE0_TEMP_CNT_SHIFT;
> > + n_meas = (val & soc_data->temp_value_mask)
> > + >> soc_data->temp_value_shift;
> >
> > Â /* See imx_init_calib() for formula derivation */
> > - *temp = data->c2 - n_meas * data->c1;
> > + if (data->socdata->version == TEMPMON_IMX7D)
> > + *temp = (n_meas - data->c1 + 25) * 1000;
> > + else
> > + *temp = data->c2 - n_meas * data->c1;
> >
> > Â /* Update alarm value to next higher trip point for
> > TEMPMON_IMX6Q */
> > Â if (data->socdata->version == TEMPMON_IMX6Q) { @@ -219,21
> > +357,26
> > @@ static int imx_set_mode(struct thermal_zone_device *tz,ÂÂ{
> > Â struct imx_thermal_data *data = tz->devdata;
> > Â struct regmap *map = data->tempmon;
> > + const struct thermal_soc_data *soc_data = data->socdata;
> >
> > Â if (mode == THERMAL_DEVICE_ENABLED) {
> > Â tz->polling_delay = IMX_POLLING_DELAY;
> > Â tz->passive_delay = IMX_PASSIVE_DELAY;
> >
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂsoc_data->power_down_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂsoc_data->measure_temp_mask);
> >
> > Â if (!data->irq_enabled) {
> > Â data->irq_enabled = true;
> > Â enable_irq(data->irq);
> > Â }
> > Â } else {
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂsoc_data->measure_temp_mask);
> > + regmap_write(map, soc_data->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂsoc_data->power_down_mask);
> >
> > Â tz->polling_delay = 0;
> > Â tz->passive_delay = 0;
> > @@ -355,6 +498,15 @@ static int imx_init_calib(struct
> > platform_device *pdev,
> > u32 ocotp_ana1)
> > Â }
> >
> > Â /*
> > + Â* On i.MX7D, we only use the calibration data at 25C to
> > get the temp,
> > + Â* Tmeas = ( Nmeas - n1) + 25; n1 is the fuse value for
> > 25C.
> > + Â*/
> > + if (data->socdata->version == TEMPMON_IMX7D) {
> > + data->c1 = (ocotp_ana1 >> 9) & 0x1ff;
> > + return 0;
> > + }
> > +
> > + /*
> > Â Â* The sensor is calibrated at 25 ÂC (aka T1) and the
> > value measured
> > Â Â* (aka N1) at this temperature is provided in bits
> > [31:20] in the
> > Â Â* i.MX's OCOTP value ANA1.
> > @@ -492,6 +644,7 @@ static irqreturn_t
> > imx_thermal_alarm_irq_thread(int
> > irq, void *dev)ÂÂstatic const struct of_device_id
> > of_imx_thermal_match[] = {
> > Â { .compatible = "fsl,imx6q-tempmon", .data =
> > &thermal_imx6q_data, },
> > Â { .compatible = "fsl,imx6sx-tempmon", .data =
> > &thermal_imx6sx_data, },
> > + { .compatible = "fsl,imx7d-tempmon", .data =
> > &thermal_imx7d_data, },
> > Â { /* end */ }
> > Â};
> > ÂMODULE_DEVICE_TABLE(of, of_imx_thermal_match); @@ -523,14 +676,15
> > @@ static int imx_thermal_probe(struct platform_device *pdev)
> >
> > Â /* make sure the IRQ flag is clear before enabling irq on
> > i.MX6SX */
> > Â if (data->socdata->version == TEMPMON_IMX6SX) {
> > - regmap_write(map, MISC1 + REG_CLR,
> > MISC1_IRQ_TEMPHIGH |
> > - MISC1_IRQ_TEMPLOW | MISC1_IRQ_TEMPPANIC);
> > + regmap_write(map, IMX6_MISC1 + REG_CLR,
> > + IMX6_MISC1_IRQ_TEMPHIGH |
> > IMX6_MISC1_IRQ_TEMPLOW
> > + | IMX6_MISC1_IRQ_TEMPPANIC);
> > Â /*
> > Â Â* reset value of LOW ALARM is incorrect, set it
> > to lowest
> > Â Â* value to avoid false trigger of low alarm.
> > Â Â*/
> > - regmap_write(map, TEMPSENSE2 + REG_SET,
> > - TEMPSENSE2_LOW_VALUE_MASK);
> > + regmap_write(map, data->socdata->low_alarm_ctrl +
> > REG_SET,
> > + ÂÂÂÂÂdata->socdata->low_alarm_mask);
> > Â }
> >
> > Â data->irq = platform_get_irq(pdev, 0); @@ -557,11 +711,17
> > @@ static int
> > imx_thermal_probe(struct platform_device *pdev)
> > Â }
> >
> > Â /* Make sure sensor is in known good state for
> > measurements */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > - regmap_write(map, MISC0 + REG_SET,
> > MISC0_REFTOP_SELBIASOFF);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂdata->socdata->measure_temp_mask);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > + ÂÂÂÂÂdata->socdata->measure_freq_mask);
> > + if (data->socdata->version != TEMPMON_IMX7D)
> > + regmap_write(map, IMX6_MISC0 + REG_SET,
> > + IMX6_MISC0_REFTOP_SELBIASOFF);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> >
> > Â data->policy = cpufreq_cpu_get(0);
> > Â if (!data->policy) {
> > @@ -626,16 +786,20 @@ static int imx_thermal_probe(struct
> > platform_device
> > *pdev)
> > Â Âdata->temp_passive / 1000);
> >
> > Â /* Enable measurements at ~ 10 Hz */
> > - regmap_write(map, TEMPSENSE1 + REG_CLR,
> > TEMPSENSE1_MEASURE_FREQ);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_CLR,
> > + ÂÂÂÂÂdata->socdata->measure_freq_mask);
> > Â measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
> > - regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
> > + regmap_write(map, data->socdata->measure_freq_ctrl +
> > REG_SET,
> > + ÂÂÂÂÂmeasure_freq << data->socdata-
> > >measure_freq_shift);
> > Â imx_set_alarm_temp(data, data->temp_passive);
> >
> > Â if (data->socdata->version == TEMPMON_IMX6SX)
> > Â imx_set_panic_temp(data, data->temp_critical);
> >
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂdata->socdata->measure_temp_mask);
> >
> > Â ret = devm_request_threaded_irq(&pdev->dev, data->irq,
> > Â imx_thermal_alarm_irq,
> > imx_thermal_alarm_irq_thread, @@
> > -661,7 +825,8 @@ static int imx_thermal_remove(struct
> > platform_device
> > *pdev)
> > Â struct regmap *map = data->tempmon;
> >
> > Â /* Disable measurements */
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> > Â if (!IS_ERR(data->thermal_clk))
> > Â clk_disable_unprepare(data->thermal_clk);
> >
> > @@ -684,8 +849,10 @@ static int imx_thermal_suspend(struct device
> > *dev)
> > Â Â* temperature will be read as the thermal sensor is
> > powered
> > Â Â* down.
> > Â Â*/
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_MEASURE_TEMP);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_POWER_DOWN);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂdata->socdata->measure_temp_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> > Â data->mode = THERMAL_DEVICE_DISABLED;
> > Â clk_disable_unprepare(data->thermal_clk);
> >
> > @@ -702,8 +869,10 @@ static int imx_thermal_resume(struct device
> > *dev)
> > Â if (ret)
> > Â return ret;
> > Â /* Enabled thermal sensor after resume */
> > - regmap_write(map, TEMPSENSE0 + REG_CLR,
> > TEMPSENSE0_POWER_DOWN);
> > - regmap_write(map, TEMPSENSE0 + REG_SET,
> > TEMPSENSE0_MEASURE_TEMP);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
> > + ÂÂÂÂÂdata->socdata->power_down_mask);
> > + regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
> > + ÂÂÂÂÂdata->socdata->measure_temp_mask);
> > Â data->mode = THERMAL_DEVICE_ENABLED;
> >
> > Â return 0;
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fl
> > ists.infr
> > adead.org%2Fmailman%2Flistinfo%2Flinux-arm-
> > kernel&data=02%7C01%7Cans
> > on.huang%40nxp.com%7C06aac542a9cb445ee0f308d57fe1cbba%7C686ea1d3
> > bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636555530125162768&sdata=GP4
> > UyKpDXyRkmwSIZY9Sb%2BDxO9sPAWCk0O%2FZPYRA0P4%3D&reserved=0