[Blackfin removal] [PATCH 05/28] rtc: Remove Blackfin RTC support
From: Aaron Wu
Date: Fri Mar 16 2018 - 03:23:18 EST
Signed-off-by: Aaron Wu <aaron.wu@xxxxxxxxxx>
Remove Blackfin RTC support
---
drivers/rtc/Kconfig | 10 --
drivers/rtc/Makefile | 1 -
drivers/rtc/rtc-bfin.c | 448 -------------------------------------------------
3 files changed, 459 deletions(-)
delete mode 100644 drivers/rtc/rtc-bfin.c
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 8ab5f0a5..622d0ed2 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1434,16 +1434,6 @@ config RTC_DRV_AU1XXX
This driver can also be built as a module. If so, the module
will be called rtc-au1xxx.
-config RTC_DRV_BFIN
- tristate "Blackfin On-Chip RTC"
- depends on BLACKFIN && !BF561
- help
- If you say yes here you will get support for the
- Blackfin On-Chip Real Time Clock.
-
- This driver can also be built as a module. If so, the module
- will be called rtc-bfin.
-
config RTC_DRV_RS5C313
tristate "Ricoh RS5C313"
depends on SH_LANDISK
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 4fbf87e4..014c8a8 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_RTC_DRV_ASM9260) += rtc-asm9260.o
obj-$(CONFIG_RTC_DRV_AT91RM9200)+= rtc-at91rm9200.o
obj-$(CONFIG_RTC_DRV_AT91SAM9) += rtc-at91sam9.o
obj-$(CONFIG_RTC_DRV_AU1XXX) += rtc-au1xxx.o
-obj-$(CONFIG_RTC_DRV_BFIN) += rtc-bfin.o
obj-$(CONFIG_RTC_DRV_BRCMSTB) += rtc-brcmstb-waketimer.o
obj-$(CONFIG_RTC_DRV_BQ32K) += rtc-bq32k.o
obj-$(CONFIG_RTC_DRV_BQ4802) += rtc-bq4802.o
diff --git a/drivers/rtc/rtc-bfin.c b/drivers/rtc/rtc-bfin.c
deleted file mode 100644
index 15344b7..0000000
--- a/drivers/rtc/rtc-bfin.c
+++ /dev/null
@@ -1,448 +0,0 @@
-/*
- * Blackfin On-Chip Real Time Clock Driver
- * Supports BF51x/BF52x/BF53[123]/BF53[467]/BF54x
- *
- * Copyright 2004-2010 Analog Devices Inc.
- *
- * Enter bugs at http://blackfin.uclinux.org/
- *
- * Licensed under the GPL-2 or later.
- */
-
-/* The biggest issue we deal with in this driver is that register writes are
- * synced to the RTC frequency of 1Hz. So if you write to a register and
- * attempt to write again before the first write has completed, the new write
- * is simply discarded. This can easily be troublesome if userspace disables
- * one event (say periodic) and then right after enables an event (say alarm).
- * Since all events are maintained in the same interrupt mask register, if
- * we wrote to it to disable the first event and then wrote to it again to
- * enable the second event, that second event would not be enabled as the
- * write would be discarded and things quickly fall apart.
- *
- * To keep this delay from significantly degrading performance (we, in theory,
- * would have to sleep for up to 1 second every time we wanted to write a
- * register), we only check the write pending status before we start to issue
- * a new write. We bank on the idea that it doesn't matter when the sync
- * happens so long as we don't attempt another write before it does. The only
- * time userspace would take this penalty is when they try and do multiple
- * operations right after another ... but in this case, they need to take the
- * sync penalty, so we should be OK.
- *
- * Also note that the RTC_ISTAT register does not suffer this penalty; its
- * writes to clear status registers complete immediately.
- */
-
-/* It may seem odd that there is no SWCNT code in here (which would be exposed
- * via the periodic interrupt event, or PIE). Since the Blackfin RTC peripheral
- * runs in units of seconds (N/HZ) but the Linux framework runs in units of HZ
- * (2^N HZ), there is no point in keeping code that only provides 1 HZ PIEs.
- * The same exact behavior can be accomplished by using the update interrupt
- * event (UIE). Maybe down the line the RTC peripheral will suck less in which
- * case we can re-introduce PIE support.
- */
-
-#include <linux/bcd.h>
-#include <linux/completion.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/rtc.h>
-#include <linux/seq_file.h>
-#include <linux/slab.h>
-
-#include <asm/blackfin.h>
-
-#define dev_dbg_stamp(dev) dev_dbg(dev, "%s:%i: here i am\n", __func__, __LINE__)
-
-struct bfin_rtc {
- struct rtc_device *rtc_dev;
- struct rtc_time rtc_alarm;
- u16 rtc_wrote_regs;
-};
-
-/* Bit values for the ISTAT / ICTL registers */
-#define RTC_ISTAT_WRITE_COMPLETE 0x8000
-#define RTC_ISTAT_WRITE_PENDING 0x4000
-#define RTC_ISTAT_ALARM_DAY 0x0040
-#define RTC_ISTAT_24HR 0x0020
-#define RTC_ISTAT_HOUR 0x0010
-#define RTC_ISTAT_MIN 0x0008
-#define RTC_ISTAT_SEC 0x0004
-#define RTC_ISTAT_ALARM 0x0002
-#define RTC_ISTAT_STOPWATCH 0x0001
-
-/* Shift values for RTC_STAT register */
-#define DAY_BITS_OFF 17
-#define HOUR_BITS_OFF 12
-#define MIN_BITS_OFF 6
-#define SEC_BITS_OFF 0
-
-/* Some helper functions to convert between the common RTC notion of time
- * and the internal Blackfin notion that is encoded in 32bits.
- */
-static inline u32 rtc_time_to_bfin(unsigned long now)
-{
- u32 sec = (now % 60);
- u32 min = (now % (60 * 60)) / 60;
- u32 hour = (now % (60 * 60 * 24)) / (60 * 60);
- u32 days = (now / (60 * 60 * 24));
- return (sec << SEC_BITS_OFF) +
- (min << MIN_BITS_OFF) +
- (hour << HOUR_BITS_OFF) +
- (days << DAY_BITS_OFF);
-}
-static inline unsigned long rtc_bfin_to_time(u32 rtc_bfin)
-{
- return (((rtc_bfin >> SEC_BITS_OFF) & 0x003F)) +
- (((rtc_bfin >> MIN_BITS_OFF) & 0x003F) * 60) +
- (((rtc_bfin >> HOUR_BITS_OFF) & 0x001F) * 60 * 60) +
- (((rtc_bfin >> DAY_BITS_OFF) & 0x7FFF) * 60 * 60 * 24);
-}
-static inline void rtc_bfin_to_tm(u32 rtc_bfin, struct rtc_time *tm)
-{
- rtc_time_to_tm(rtc_bfin_to_time(rtc_bfin), tm);
-}
-
-/**
- * bfin_rtc_sync_pending - make sure pending writes have complete
- *
- * Wait for the previous write to a RTC register to complete.
- * Unfortunately, we can't sleep here as that introduces a race condition when
- * turning on interrupt events. Consider this:
- * - process sets alarm
- * - process enables alarm
- * - process sleeps while waiting for rtc write to sync
- * - interrupt fires while process is sleeping
- * - interrupt acks the event by writing to ISTAT
- * - interrupt sets the WRITE PENDING bit
- * - interrupt handler finishes
- * - process wakes up, sees WRITE PENDING bit set, goes to sleep
- * - interrupt fires while process is sleeping
- * If anyone can point out the obvious solution here, i'm listening :). This
- * shouldn't be an issue on an SMP or preempt system as this function should
- * only be called with the rtc lock held.
- *
- * Other options:
- * - disable PREN so the sync happens at 32.768kHZ ... but this changes the
- * inc rate for all RTC registers from 1HZ to 32.768kHZ ...
- * - use the write complete IRQ
- */
-/*
-static void bfin_rtc_sync_pending_polled(void)
-{
- while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_COMPLETE))
- if (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING))
- break;
- bfin_write_RTC_ISTAT(RTC_ISTAT_WRITE_COMPLETE);
-}
-*/
-static DECLARE_COMPLETION(bfin_write_complete);
-static void bfin_rtc_sync_pending(struct device *dev)
-{
- dev_dbg_stamp(dev);
- while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING)
- wait_for_completion_timeout(&bfin_write_complete, HZ * 5);
- dev_dbg_stamp(dev);
-}
-
-/**
- * bfin_rtc_reset - set RTC to sane/known state
- *
- * Initialize the RTC. Enable pre-scaler to scale RTC clock
- * to 1Hz and clear interrupt/status registers.
- */
-static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
- dev_dbg_stamp(dev);
- bfin_rtc_sync_pending(dev);
- bfin_write_RTC_PREN(0x1);
- bfin_write_RTC_ICTL(rtc_ictl);
- bfin_write_RTC_ALARM(0);
- bfin_write_RTC_ISTAT(0xFFFF);
- rtc->rtc_wrote_regs = 0;
-}
-
-/**
- * bfin_rtc_interrupt - handle interrupt from RTC
- *
- * Since we handle all RTC events here, we have to make sure the requested
- * interrupt is enabled (in RTC_ICTL) as the event status register (RTC_ISTAT)
- * always gets updated regardless of the interrupt being enabled. So when one
- * even we care about (e.g. stopwatch) goes off, we don't want to turn around
- * and say that other events have happened as well (e.g. second). We do not
- * have to worry about pending writes to the RTC_ICTL register as interrupts
- * only fire if they are enabled in the RTC_ICTL register.
- */
-static irqreturn_t bfin_rtc_interrupt(int irq, void *dev_id)
-{
- struct device *dev = dev_id;
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
- unsigned long events = 0;
- bool write_complete = false;
- u16 rtc_istat, rtc_istat_clear, rtc_ictl, bits;
-
- dev_dbg_stamp(dev);
-
- rtc_istat = bfin_read_RTC_ISTAT();
- rtc_ictl = bfin_read_RTC_ICTL();
- rtc_istat_clear = 0;
-
- bits = RTC_ISTAT_WRITE_COMPLETE;
- if (rtc_istat & bits) {
- rtc_istat_clear |= bits;
- write_complete = true;
- complete(&bfin_write_complete);
- }
-
- bits = (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY);
- if (rtc_ictl & bits) {
- if (rtc_istat & bits) {
- rtc_istat_clear |= bits;
- events |= RTC_AF | RTC_IRQF;
- }
- }
-
- bits = RTC_ISTAT_SEC;
- if (rtc_ictl & bits) {
- if (rtc_istat & bits) {
- rtc_istat_clear |= bits;
- events |= RTC_UF | RTC_IRQF;
- }
- }
-
- if (events)
- rtc_update_irq(rtc->rtc_dev, 1, events);
-
- if (write_complete || events) {
- bfin_write_RTC_ISTAT(rtc_istat_clear);
- return IRQ_HANDLED;
- } else
- return IRQ_NONE;
-}
-
-static void bfin_rtc_int_set(u16 rtc_int)
-{
- bfin_write_RTC_ISTAT(rtc_int);
- bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() | rtc_int);
-}
-static void bfin_rtc_int_clear(u16 rtc_int)
-{
- bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() & rtc_int);
-}
-static void bfin_rtc_int_set_alarm(struct bfin_rtc *rtc)
-{
- /* Blackfin has different bits for whether the alarm is
- * more than 24 hours away.
- */
- bfin_rtc_int_set(rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY);
-}
-
-static int bfin_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
-
- dev_dbg_stamp(dev);
- if (enabled)
- bfin_rtc_int_set_alarm(rtc);
- else
- bfin_rtc_int_clear(~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
-
- return 0;
-}
-
-static int bfin_rtc_read_time(struct device *dev, struct rtc_time *tm)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
-
- dev_dbg_stamp(dev);
-
- if (rtc->rtc_wrote_regs & 0x1)
- bfin_rtc_sync_pending(dev);
-
- rtc_bfin_to_tm(bfin_read_RTC_STAT(), tm);
-
- return 0;
-}
-
-static int bfin_rtc_set_time(struct device *dev, struct rtc_time *tm)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
- int ret;
- unsigned long now;
-
- dev_dbg_stamp(dev);
-
- ret = rtc_tm_to_time(tm, &now);
- if (ret == 0) {
- if (rtc->rtc_wrote_regs & 0x1)
- bfin_rtc_sync_pending(dev);
- bfin_write_RTC_STAT(rtc_time_to_bfin(now));
- rtc->rtc_wrote_regs = 0x1;
- }
-
- return ret;
-}
-
-static int bfin_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
- dev_dbg_stamp(dev);
- alrm->time = rtc->rtc_alarm;
- bfin_rtc_sync_pending(dev);
- alrm->enabled = !!(bfin_read_RTC_ICTL() & (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
- return 0;
-}
-
-static int bfin_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
-{
- struct bfin_rtc *rtc = dev_get_drvdata(dev);
- unsigned long rtc_alarm;
-
- dev_dbg_stamp(dev);
-
- if (rtc_tm_to_time(&alrm->time, &rtc_alarm))
- return -EINVAL;
-
- rtc->rtc_alarm = alrm->time;
-
- bfin_rtc_sync_pending(dev);
- bfin_write_RTC_ALARM(rtc_time_to_bfin(rtc_alarm));
- if (alrm->enabled)
- bfin_rtc_int_set_alarm(rtc);
-
- return 0;
-}
-
-static int bfin_rtc_proc(struct device *dev, struct seq_file *seq)
-{
-#define yesno(x) ((x) ? "yes" : "no")
- u16 ictl = bfin_read_RTC_ICTL();
- dev_dbg_stamp(dev);
- seq_printf(seq,
- "alarm_IRQ\t: %s\n"
- "wkalarm_IRQ\t: %s\n"
- "seconds_IRQ\t: %s\n",
- yesno(ictl & RTC_ISTAT_ALARM),
- yesno(ictl & RTC_ISTAT_ALARM_DAY),
- yesno(ictl & RTC_ISTAT_SEC));
- return 0;
-#undef yesno
-}
-
-static const struct rtc_class_ops bfin_rtc_ops = {
- .read_time = bfin_rtc_read_time,
- .set_time = bfin_rtc_set_time,
- .read_alarm = bfin_rtc_read_alarm,
- .set_alarm = bfin_rtc_set_alarm,
- .proc = bfin_rtc_proc,
- .alarm_irq_enable = bfin_rtc_alarm_irq_enable,
-};
-
-static int bfin_rtc_probe(struct platform_device *pdev)
-{
- struct bfin_rtc *rtc;
- struct device *dev = &pdev->dev;
- int ret;
- unsigned long timeout = jiffies + HZ;
-
- dev_dbg_stamp(dev);
-
- /* Allocate memory for our RTC struct */
- rtc = devm_kzalloc(dev, sizeof(*rtc), GFP_KERNEL);
- if (unlikely(!rtc))
- return -ENOMEM;
- platform_set_drvdata(pdev, rtc);
- device_init_wakeup(dev, 1);
-
- /* Register our RTC with the RTC framework */
- rtc->rtc_dev = devm_rtc_device_register(dev, pdev->name, &bfin_rtc_ops,
- THIS_MODULE);
- if (IS_ERR(rtc->rtc_dev))
- return PTR_ERR(rtc->rtc_dev);
-
- /* Grab the IRQ and init the hardware */
- ret = devm_request_irq(dev, IRQ_RTC, bfin_rtc_interrupt, 0,
- pdev->name, dev);
- if (unlikely(ret))
- dev_err(&pdev->dev,
- "unable to request IRQ; alarm won't work, "
- "and writes will be delayed\n");
-
- /* sometimes the bootloader touched things, but the write complete was not
- * enabled, so let's just do a quick timeout here since the IRQ will not fire ...
- */
- while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING)
- if (time_after(jiffies, timeout))
- break;
- bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE);
- bfin_write_RTC_SWCNT(0);
-
- return 0;
-}
-
-static int bfin_rtc_remove(struct platform_device *pdev)
-{
- struct device *dev = &pdev->dev;
-
- bfin_rtc_reset(dev, 0);
-
- return 0;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int bfin_rtc_suspend(struct device *dev)
-{
- dev_dbg_stamp(dev);
-
- if (device_may_wakeup(dev)) {
- enable_irq_wake(IRQ_RTC);
- bfin_rtc_sync_pending(dev);
- } else
- bfin_rtc_int_clear(0);
-
- return 0;
-}
-
-static int bfin_rtc_resume(struct device *dev)
-{
- dev_dbg_stamp(dev);
-
- if (device_may_wakeup(dev))
- disable_irq_wake(IRQ_RTC);
-
- /*
- * Since only some of the RTC bits are maintained externally in the
- * Vbat domain, we need to wait for the RTC MMRs to be synced into
- * the core after waking up. This happens every RTC 1HZ. Once that
- * has happened, we can go ahead and re-enable the important write
- * complete interrupt event.
- */
- while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_SEC))
- continue;
- bfin_rtc_int_set(RTC_ISTAT_WRITE_COMPLETE);
-
- return 0;
-}
-#endif
-
-static SIMPLE_DEV_PM_OPS(bfin_rtc_pm_ops, bfin_rtc_suspend, bfin_rtc_resume);
-
-static struct platform_driver bfin_rtc_driver = {
- .driver = {
- .name = "rtc-bfin",
- .pm = &bfin_rtc_pm_ops,
- },
- .probe = bfin_rtc_probe,
- .remove = bfin_rtc_remove,
-};
-
-module_platform_driver(bfin_rtc_driver);
-
-MODULE_DESCRIPTION("Blackfin On-Chip Real Time Clock Driver");
-MODULE_AUTHOR("Mike Frysinger <vapier@xxxxxxxxxx>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:rtc-bfin");
--
2.7.4