[PATCH AUTOSEL for 4.9 052/281] arm64: perf: Ignore exclude_hv when kernel is running in HYP

[Sasha Levin]

From: Ganapatrao Kulkarni <ganapatrao.kulkarni@xxxxxxxxxx>

[ Upstream commit 78a19cfdf37d19002c83c8790853c1cc10feccdc ]

commit d98ecdaca296 ("arm64: perf: Count EL2 events if the kernel is
running in HYP") returns -EINVAL when perf system call perf_event_open is
called with exclude_hv != exclude_kernel. This change breaks applications
on VHE enabled ARMv8.1 platforms. The issue was observed with HHVM
application, which calls perf_event_open with exclude_hv = 1 and
exclude_kernel = 0.

There is no separate hypervisor privilege level when VHE is enabled, the
host kernel runs at EL2. So when VHE is enabled, we should ignore
exclude_hv from the application. This behaviour is consistent with PowerPC
where the exclude_hv is ignored when the hypervisor is not present and with
x86 where this flag is ignored.

Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@xxxxxxxxxx>
[will: added comment to justify the behaviour of exclude_hv]
Signed-off-by: Will Deacon <will.deacon@xxxxxxx>
Signed-off-by: Catalin Marinas <catalin.marinas@xxxxxxx>
Signed-off-by: Sasha Levin <alexander.levin@xxxxxxxxxxxxx>
---
 arch/arm64/kernel/perf_event.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/kernel/perf_event.c b/arch/arm64/kernel/perf_event.c
index 57ae9d9ed9bb..199a23f058d5 100644
--- a/arch/arm64/kernel/perf_event.c
+++ b/arch/arm64/kernel/perf_event.c
@@ -871,15 +871,24 @@ static int armv8pmu_set_event_filter(struct hw_perf_event *event,
 
 	if (attr->exclude_idle)
 		return -EPERM;
-	if (is_kernel_in_hyp_mode() &&
-	    attr->exclude_kernel != attr->exclude_hv)
-		return -EINVAL;
+
+	/*
+	 * If we're running in hyp mode, then we *are* the hypervisor.
+	 * Therefore we ignore exclude_hv in this configuration, since
+	 * there's no hypervisor to sample anyway. This is consistent
+	 * with other architectures (x86 and Power).
+	 */
+	if (is_kernel_in_hyp_mode()) {
+		if (!attr->exclude_kernel)
+			config_base |= ARMV8_PMU_INCLUDE_EL2;
+	} else {
+		if (attr->exclude_kernel)
+			config_base |= ARMV8_PMU_EXCLUDE_EL1;
+		if (!attr->exclude_hv)
+			config_base |= ARMV8_PMU_INCLUDE_EL2;
+	}
 	if (attr->exclude_user)
 		config_base |= ARMV8_PMU_EXCLUDE_EL0;
-	if (!is_kernel_in_hyp_mode() && attr->exclude_kernel)
-		config_base |= ARMV8_PMU_EXCLUDE_EL1;
-	if (!attr->exclude_hv)
-		config_base |= ARMV8_PMU_INCLUDE_EL2;
 
 	/*
 	 * Install the filter into config_base as this is used to
-- 
2.14.1