Re: [PATCH v4 0/8] ARM: davinci: complete the conversion to using the reset framework
From: Suman Anna
Date: Mon Mar 26 2018 - 20:44:02 EST
Hi Bart,
On 03/23/2018 07:30 PM, Suman Anna wrote:
> Hi Bart,
>
> On 03/23/2018 12:16 PM, Bartosz Golaszewski wrote:
>> 2018-03-23 18:08 GMT+01:00 Stephen Boyd <sboyd@xxxxxxxxxx>:
>>> Quoting Bartosz Golaszewski (2018-03-23 09:55:47)
>>>> 2018-03-23 17:49 GMT+01:00 Stephen Boyd <sboyd@xxxxxxxxxx>:
>>>>> Quoting Bartosz Golaszewski (2018-03-23 06:04:47)
>>>>>> From: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
>>>>>>
>>>>>> This series converts the only user of the handcoded, mach-specific reset
>>>>>> routines in the davinci platform to using the reset framework.
>>>>>>
>>>>>> Patch 1 modifies the way lookup entries are registered with the reset
>>>>>> framework.
>>>>>>
>>>>>> Patches 2-4 add necessary lookups/DT-properties.
>>>>>>
>>>>>> Patches 5-7 convert the davinci-rproc driver to the reset framework.
>>>>>>
>>>>>> Patch 8 removes now dead code.
>>>>>>
>>>>>> Philipp: it turned out that it's indeed better to use the reset
>>>>>> controller's device name for the entry lookup.
>>>>>>
>>>>>> Tested both in DT and legacy modes by booting the examples from
>>>>>> ti-ipc-rtos recipe in meta-ti.
>>>>>>
>>>>>> This series applies on top of David Lechner's common-clk-v9 branch[1]
>>>>>> with Philipp Zabel's reset/next branch[2] pulled in.
>>>>>>
>>>>>> It can be found in my github tree as well[3].
>>>>>>
>>>>>
>>>>> What's the merge strategy for the rest of the patches? I should apply
>>>>> the clk ones after the next -rc1?
>>>>
>>>> Or maybe Philipp can provide us with an immutable branch with the reset patches?
>>>>
>>>> The you could apply the driver patches and let Sekhar take all the
>>>> platform code?
>>>>
>>>
>>> Ok that could work too.
>>
>> Ohad, Bjorn can you ack the remoteproc patches? Are you OK with
>> Stephen taking them through the clock tree? Otherwise it would get
>> complicated since they depend on the first clk patch and the last clk
>> patch depends on them.
>
> I will take a closer look and test on Mon. A quick glance of the
> remoteproc changes seem to be fine. I will let Bjorn comment on the
> patch flow.
>
> The only reason I had to use the clock in the driver was for the reset
> before, and hopefully this will allow me to actually switch to using
> pm_runtime API like I do with the rest of the TI remoteproc drivers
> (Keystone remoteproc driver also uses PSC for clock and reset but then
> it goes through different set of drivers).
>
> So, I see a mix of driver and dts patches in the series, are all the dts
> patches coming through Sekhar?
I tried booting your tree [3] on the OMAPL138-LCDK board. I am using
NFS, and I am unable to get to the console. I don't have any issues
booting latest -next branch (next-20180326) which only has the reset and
clock driver related changes.
Here's the log towards the end of the boot..
---
pinctrl-single 1c14120.pinmux: 160 pins, size 80
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
console [ttyS2] disabled
1d0d000.serial: ttyS2 at MMIO 0x1d0d000 (irq = 61, base_baud = 8250000)
is a TI DA8xx/66AK2x
console [ttyS2] enabled
brd: module loaded
libphy: Fixed MDIO Bus: probed
davinci_mdio 1e24000.mdio: davinci mdio revision 1.5, bus freq 2200000
davinci_mdio 1e24000.mdio: no live phy, scanning all
davinci_mdio: probe of 1e24000.mdio failed with error -5
i2c /dev entries driver
<nothing after this>
regards
Suman
>
> regards
> Suman
>
>>
>> Thanks,
>> Bart
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-remoteproc" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-remoteproc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>