Re: [PATCH v6 1/3] dt-bindings: display: bridge: Document THC63LVD1024 LVDS decoder
From: jacopo mondi
Date: Tue Mar 27 2018 - 03:33:47 EST
Hi Andrzej,
On Tue, Mar 27, 2018 at 09:12:46AM +0200, Andrzej Hajda wrote:
> On 27.03.2018 08:15, Vladimir Zapolskiy wrote:
> > Hi Jacopo,
> >
> > On 03/27/2018 01:22 AM, Rob Herring wrote:
> >> On Tue, Mar 20, 2018 at 02:43:33PM +0200, Laurent Pinchart wrote:
> >>> Hi Jacopo,
> >>>
> >>> (CC'ing Rob)
> >>>
> >>> Thank you for the patch.
> >>>
> >>> On Friday, 16 March 2018 17:16:37 EET Jacopo Mondi wrote:
> >>>> Document Thine THC63LVD1024 LVDS decoder device tree bindings.
> >>>>
> >>>> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> >>>> Reviewed-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> >>>> Reviewed-by: Niklas SÃderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> >>>> ---
> >>>> .../bindings/display/bridge/thine,thc63lvd1024.txt | 66 +++++++++++++++++++
> >>>> 1 file changed, 66 insertions(+)
> >>>> create mode 100644
> >>>> Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >>>>
> >>>> diff --git
> >>>> a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >>>> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >>>> new file mode 100644
> >>>> index 0000000..8225c6a
> >>>> --- /dev/null
> >>>> +++
> >>>> b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >>>> @@ -0,0 +1,66 @@
> >>>> +Thine Electronics THC63LVD1024 LVDS decoder
> >>>> +-------------------------------------------
> >>>> +
> >>>> +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS
> >>>> streams
> >>>> +to parallel data outputs. The chip supports single/dual input/output modes,
> >>>> +handling up to two two input LVDS stream and up to two digital CMOS/TTL
> >>>> outputs.
> >>>> +
> >>>> +Single or dual operation modes, output data mapping and DDR output modes
> >>>> are
> >>>> +configured through input signals and the chip does not expose any control
> >>>> bus.
> >>>> +
> >>>> +Required properties:
> >>>> +- compatible: Shall be "thine,thc63lvd1024"
> >>>> +
> >>>> +Optional properties:
> >>>> +- vcc-supply: Power supply for TTL output and digital circuitry
> >>>> +- cvcc-supply: Power supply for TTL CLOCKOUT signal
> >>>> +- lvcc-supply: Power supply for LVDS inputs
> >>>> +- pvcc-supply: Power supply for PLL circuitry
> >>> As explained in a comment to one of the previous versions of this series, I'm
> >>> tempted to make vcc-supply mandatory and drop the three other power supplies
> >>> for now, as I believe there's very little chance they will be connected to
> >>> separately controllable regulators (all supplies use the same voltage). In the
> >>> very unlikely event that this occurs in design we need to support in the
> >>> future, the cvcc, lvcc and pvcc supplies can be added later as optional
> >>> without breaking backward compatibility.
> >> I'm okay with that.
> >>
> >>> Apart from that,
> >>>
> >>> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> >>>
> >>>> +- pdwn-gpios: Power down GPIO signal. Active low
> >> powerdown-gpios is the semi-standard name.
> >>
> > right, I've also noticed it. If possible please avoid shortenings in
> > property names.
>
> It is not shortening, it just follow pin name from decoder's datasheet.
>
> >
> >>>> +- oe-gpios: Output enable GPIO signal. Active high
> >>>> +
> > And this one is also a not ever met property name, please consider to
> > rename it to 'enable-gpios', for instance display panels define it.
>
>
> Again, it follows datasheet naming scheme. Has something changed in DT
> conventions?
Seconded. My understanding is that the property name should reflect
what reported in the the chip manual. For THC63LVD1024 the enable and
power down pins are named 'OE' and 'PDWN' respectively.
Thanks
j
>
> Regards
> Andrzej
>
> >
> >>>> +The THC63LVD1024 video port connections are modeled according
> >>>> +to OF graph bindings specified by
> >>>> Documentation/devicetree/bindings/graph.txt
> > [snip]
> >
> >>>> +
> >>>> + port@2{
> >>>> + reg = <2>;
> >>>> +
> >>>> + lvds_dec_out_2: endpoint {
> >>>> + remote-endpoint = <&adv7511_in>;
> >>>> + };
> >>>> +
> > Drop a surplus empty line above.
> >
> >>>> + };
> >>>> +
> > Drop a surplus empty line above.
> >
> >>>> + };
> >>>> + };
> > --
> > With best wishes,
> > Vladimir
> >
> >
> >
>