Re: [PATCH] mtd: nand: raw: atmel: add module param to avoid using dma
From: Boris Brezillon
Date: Mon Apr 02 2018 - 08:22:58 EST
On Thu, 29 Mar 2018 16:27:12 +0200
Peter Rosin <peda@xxxxxxxxxx> wrote:
> On 2018-03-29 15:44, Boris Brezillon wrote:
> > On Thu, 29 Mar 2018 15:37:43 +0200
> > Peter Rosin <peda@xxxxxxxxxx> wrote:
> >
> >> On 2018-03-29 15:33, Boris Brezillon wrote:
> >>> On Thu, 29 Mar 2018 15:10:54 +0200
> >>> Peter Rosin <peda@xxxxxxxxxx> wrote:
> >>>
> >>>> On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
> >>>> flash accesses have a tendency to cause display disturbances. Add a
> >>>> module param to disable DMA from the NAND controller, since that fixes
> >>>> the display problem for me.
> >>>>
> >>>> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx>
> >>>> ---
> >>>> drivers/mtd/nand/raw/atmel/nand-controller.c | 7 ++++++-
> >>>> 1 file changed, 6 insertions(+), 1 deletion(-)
> >>>>
> >>>> diff --git a/drivers/mtd/nand/raw/atmel/nand-controller.c b/drivers/mtd/nand/raw/atmel/nand-controller.c
> >>>> index b2f00b398490..2ff7a77c7b8e 100644
> >>>> --- a/drivers/mtd/nand/raw/atmel/nand-controller.c
> >>>> +++ b/drivers/mtd/nand/raw/atmel/nand-controller.c
> >>>> @@ -129,6 +129,11 @@
> >>>> #define DEFAULT_TIMEOUT_MS 1000
> >>>> #define MIN_DMA_LEN 128
> >>>>
> >>>> +static bool atmel_nand_avoid_dma __read_mostly;
> >>>> +
> >>>> +MODULE_PARM_DESC(avoiddma, "Avoid using DMA");
> >>>> +module_param_named(avoiddma, atmel_nand_avoid_dma, bool, 0400);
> >>>
> >>> I'm not a big fan of those driver specific cmdline parameters. Can't we
> >>> instead give an higher priority to HLCDC master using the bus matrix?
> >>
> >> I don't know if it will be enough, but we sure can try. However, I have
> >> no idea how to do that. I will happily test stuff though...
> >
> > There's no interface to configure that from Linux, but you can try to
> > tweak it with devmem and if that does the trick, maybe we can expose a
> > way to configure that from Linux. For more details, see the "Bus Matrix
> > (MATRIX)" section in Atmel datasheets.
>
> I don't seem to succeed in changing the registers I think I need to change.
> I can poke the "Write Protection Mode Register" by writing MAT0 and MAT1 to
> it.
You mean 0x4D415400, right? ("MAT0" != 0x4D415400).
> But when I try to write to "Priority Registers B For Slaves" it doesn't
> take, regardless of write protect mode.
Did you check MATRIX_WPSR after writing to MATRIX_PRXSY?
>
> Can the relevant bits only be written when the HLCDC is inactive or
> something?
I don't know, but maybe Nicolas does.
--
Boris Brezillon, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com