Re: [PATCHv4 09/10] dt-bindings: mfd: ti-lmu: update for backlight

[Sebastian Reichel]

Hi,

On Mon, Apr 09, 2018 at 04:06:38PM -0500, Rob Herring wrote:
> On Fri, Mar 30, 2018 at 07:24:13PM +0200, Sebastian Reichel wrote:
> > Update binding to integrate the backlight feature directly into
> > the main node, as suggested by Rob Herring.
> > 
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
> > ---
> >  Documentation/devicetree/bindings/mfd/ti-lmu.txt | 119 ++++++++++++-----------
> >  1 file changed, 60 insertions(+), 59 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > index c885cf89b8ce..b3433e95dfa5 100644
> > --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > @@ -28,10 +28,9 @@ Required properties:
> >  
> >  Optional property:
> >    - enable-gpios: A GPIO specifier for hardware enable pin.
> > -
> > -Required node:
> > -  - backlight: All LMU devices have backlight child nodes.
> > -               For the properties, please refer to [1].
> > +  - pwm-names: Should be either "lmu-backlight" or unset
> > +  - pwm: This should be a PWM specifier following ../pwm/pwm.txt and must
> > +         only be specified, if the backlight should be used in PWM mode.
> >  
> >  Optional nodes:
> >    - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697.
> > @@ -42,8 +41,31 @@ Optional nodes:
> >    - leds: LED properties for LM3633. Please refer to [2].
> >    - regulators: Regulator properties for LM3631 and LM3632.
> >                  Please refer to [3].
> > +  - bank0, bank1, bank2: This contains the backlight configuration
> > +                         for each backlight control bank.
> > +
> > +Required properties in the bank subnodes:
> > +  - label: A string describing the backlight. Should contain "keyboard"
> > +           for a keyboard backlight and "lcd" for LCD panel backlights.
> > +  - ti,led-sources: A list of channels, that should be driven. Each channel
> > +                    should only be driven by one bank.
> > +
> > +Optional properties in the bank subnodes:
> > +  - default-brightness-level: Backlight initial brightness value.
> > +                              Type is <u32>. It is set as soon as backlight
> > +			      device is created.
> > +			      0 ~ 2047 = LM3631, LM3632, LM3633, LM3695 and
> > +					 LM3697
> > +			      0 ~ 255  = LM3532
> > +  - ti,ramp-up-ms, ti,ramp-down-ms: Light dimming effect properties.
> > +				    Type is <u32>. Unit is millisecond.
> > +					0 ~ 65 ms    = LM3532
> > +					0 ~ 4000 ms  = LM3631
> > +					0 ~ 16000 ms = LM3633 and LM3697
> > +  - pwm-period: PWM period. Only valid in PWM brightness mode.
> > +                Type is <u32>. If this property is missing, then control
> > +		mode is set to I2C by default.
> >  
> > -[1] ../leds/backlight/ti-lmu-backlight.txt
> >  [2] ../leds/leds-lm3633.txt
> >  [3] ../regulator/lm363x-regulator.txt
> >  
> > @@ -53,14 +75,11 @@ lm3532@38 {
> >  
> >  	enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
> >  
> > -	backlight {
> > -		compatible = "ti,lm3532-backlight";
> > -
> > -		lcd {
> > -			led-sources = <0 1 2>;
> > -			ramp-up-msec = <30>;
> > -			ramp-down-msec = <0>;
> > -		};
> > +	bank0 {
> > +		label = "lcd";
> > +		led-sources = <0 1 2>;
> > +		ramp-up-msec = <30>;
> > +		ramp-down-msec = <0>;
> 
> Looks like it was already wrong, but these are missing the vendor 
> prefixes.

Oops. I will add the vendor prefix.

> 
> >  	};
> >  };
> >  
> > @@ -105,13 +124,10 @@ lm3631@29 {
> 
> Are so many examples really needed? Examples aren't supposed to 
> enumerate all possible options...

I will remove a few in the next version.

-- Sebastian

Attachment: signature.asc
Description: PGP signature