[PATCH 00/17] thermal: enable/check sensor after its setup is finished

[Bartlomiej Zolnierkiewicz]

Hi,

[devm]_thermal_zone_of_sensor_register() is used to register
thermal sensor by thermal drivers using DeviceTree. Besides
registering sensor this function also immediately enables it
(using ->set_mode method) and then checks it with a update call
to the thermal core (which ends up using ->get_temp method).
For many DT thermal drivers this causes a problem because
[devm]_thermal_zone_of_sensor_register() need to be called in
order to obtain data about thermal trips which are then used to
finish hardware sensor setup (only after which ->get_temp can
be used). The issue has been observed when using Samsung Exynos
thermal driver and fixed internally in the driver in commit
d8efad71e5b6 ("thermal: exynos: Reading temperature makes sense
only when TMU is turned on"). However after this commit there
are now following warnings from the thermal core visible:

[    3.453602] thermal thermal_zone0: failed to read out thermal zone (-22)
[    3.483468] thermal thermal_zone1: failed to read out thermal zone (-22)
[    3.505965] thermal thermal_zone2: failed to read out thermal zone (-22)
[    3.528455] thermal thermal_zone3: failed to read out thermal zone (-22)
[    3.550939] thermal thermal_zone4: failed to read out thermal zone (-22)

This patchset attempts to directly address the thermal core
problem with [devm]_thermal_zone_of_sensor_register() and
affected DT thermal drivers. In order to achieve this sensor
registration, enable and check operations are separated and
corresponding drivers are modified to use the new helpers to
enable and check sensor explicitly.

Tested on Exynos5422 based Odroid-XU3 Lite board (aforementioned
warnings from the thermal core are now gone).

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics


Bartlomiej Zolnierkiewicz (17):
  thermal: add thermal_zone_device_toggle() helper
  thermal: separate sensor registration and enable
  thermal: add thermal_zone_device_check() helper
  thermal: do sensor checking explicitly in drivers
  thermal: bcm2835: enable/check sensor after its setup is finished
  thermal: brcmstb: enable/check sensor after its setup is finished
  thermal: hisi_thermal: enable/check sensor after its setup is finished
  thermal: qcom: tsens: enable/check sensor after its setup is finished
  thermal: qoriq: enable/check sensor after its setup is finished
  thermal: rcar_gen3_thermal: enable/check sensor after its setup is
    finished
  thermal: rockchip_thermal: enable/check sensor after its setup is
    finished
  thermal: exynos: enable/check sensor after its setup is finished
  thermal: tegra: enable/check sensor after its setup is finished
  thermal: ti-soc-thermal: enable/check sensor after its setup is
    finished
  thermal: uniphier: enable/check sensor after its setup is
    finished
  thermal: zx2967: enable/check sensor after its setup is finished
  thermal: warn on attempts to read temperature on disabled sensors

 drivers/acpi/thermal.c                             |  5 ++--
 drivers/net/ethernet/mellanox/mlxsw/core_thermal.c |  1 -
 drivers/platform/x86/acerhdf.c                     |  6 +++-
 drivers/regulator/max8973-regulator.c              |  3 +-
 drivers/thermal/broadcom/bcm2835_thermal.c         |  3 ++
 drivers/thermal/broadcom/brcmstb_thermal.c         |  3 ++
 drivers/thermal/broadcom/ns-thermal.c              |  3 ++
 drivers/thermal/da9062-thermal.c                   |  7 ++---
 drivers/thermal/db8500_thermal.c                   |  5 +++-
 drivers/thermal/hisi_thermal.c                     | 22 ++++----------
 drivers/thermal/imx_thermal.c                      |  3 +-
 drivers/thermal/int340x_thermal/int3400_thermal.c  |  1 +
 drivers/thermal/intel_bxt_pmic_thermal.c           |  3 +-
 drivers/thermal/intel_soc_dts_iosf.c               |  3 +-
 drivers/thermal/max77620_thermal.c                 |  6 ++--
 drivers/thermal/mtk_thermal.c                      |  3 ++
 drivers/thermal/of-thermal.c                       |  6 ++--
 drivers/thermal/qcom-spmi-temp-alarm.c             |  5 +++-
 drivers/thermal/qcom/tsens.c                       |  6 ++++
 drivers/thermal/qoriq_thermal.c                    |  3 ++
 drivers/thermal/rcar_gen3_thermal.c                |  7 +++--
 drivers/thermal/rcar_thermal.c                     |  8 +++--
 drivers/thermal/rockchip_thermal.c                 | 34 ++++++++++------------
 drivers/thermal/samsung/exynos_tmu.c               |  7 ++++-
 drivers/thermal/st/st_thermal_memmap.c             |  3 +-
 drivers/thermal/tango_thermal.c                    |  5 ++++
 drivers/thermal/tegra/soctherm.c                   |  3 ++
 drivers/thermal/tegra/tegra-bpmp-thermal.c         |  3 ++
 drivers/thermal/thermal-generic-adc.c              |  3 ++
 drivers/thermal/thermal_core.c                     | 14 ++++-----
 drivers/thermal/thermal_helpers.c                  | 33 +++++++++++++++++++++
 drivers/thermal/thermal_sysfs.c                    | 17 +++++++----
 drivers/thermal/ti-soc-thermal/ti-thermal-common.c |  7 ++++-
 drivers/thermal/uniphier_thermal.c                 |  6 +++-
 drivers/thermal/x86_pkg_temp_thermal.c             |  2 +-
 drivers/thermal/zx2967_thermal.c                   |  3 ++
 include/linux/thermal.h                            |  5 ++++
 37 files changed, 173 insertions(+), 84 deletions(-)

-- 
1.9.1