Re: [PATCH v2] ARM: dts: tpc: Device tree description of the iMX6Q TPC board
From: Lukasz Majewski
Date: Tue Apr 10 2018 - 10:09:02 EST
Hi Rob,
> On Tue, Apr 03, 2018 at 06:59:45PM +0200, Lukasz Majewski wrote:
> > This commit adds device tree description of Kieback & Peter GmbH
> > iMX6Q TPC board.
> >
> > Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
> >
> > ---
> > Changes for v2:
> > - SDPX license identifiers used
> > - Separate regulators
> > - Proper beeper driver
> > - Use of the lcd panel (with compatible) instead of timings
> > provided in device tree
> > - Add IRQ types (like IRQ_TYPE_EDGE_FALLING) and GPIO active levels
> > (like GPIO_ACTIVE_HIGH)
> > - Remove not needed nodes
> > - Make W=1 dtbs compilation with no errors
> > ---
> > .../devicetree/bindings/vendor-prefixes.txt | 1 +
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6q-kp-tpc.dts | 23 ++
> > arch/arm/boot/dts/imx6q-kp.dtsi | 460
> > +++++++++++++++++++++ 4 files changed, 485 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6q-kp-tpc.dts
> > create mode 100644 arch/arm/boot/dts/imx6q-kp.dtsi
> >
> > diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt
> > b/Documentation/devicetree/bindings/vendor-prefixes.txt index
> > ae850d6c0ad3..8ff7eadc8bef 100644 ---
> > a/Documentation/devicetree/bindings/vendor-prefixes.txt +++
> > b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -181,6
> > +181,7 @@ karo Ka-Ro electronics GmbH keithkoep Keith
> > & Koep GmbH keymile Keymile GmbH
> > khadas Khadas
> > +kiebackpeter Kieback & Peter GmbH
> > kinetic Kinetic Technologies
> > kingnovel Kingnovel Technology Co., Ltd.
> > kosagi Sutajio Ko-Usagi PTE Ltd.
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index ade7a38543dc..c148c4cf28f2 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -459,6 +459,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6q-icore-ofcap10.dtb \
> > imx6q-icore-ofcap12.dtb \
> > imx6q-icore-rqs.dtb \
> > + imx6q-kp-tpc.dtb \
> > imx6q-marsboard.dtb \
> > imx6q-mccmon6.dtb \
> > imx6q-nitrogen6x.dtb \
> > diff --git a/arch/arm/boot/dts/imx6q-kp-tpc.dts
> > b/arch/arm/boot/dts/imx6q-kp-tpc.dts new file mode 100644
> > index 000000000000..b5646040b516
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-kp-tpc.dts
> > @@ -0,0 +1,23 @@
> > +/*
> > + * Copyright 2018
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>
> This goes on the first line. checkpatch.pl will tell you this.
I've today sent the v4 of this patch. It was fixed in this version.
>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q-kp.dtsi"
> > +
> > +/ {
> > + model = "Freescale i.MX6 Qwuad K+P TPC Board";
> > + compatible = "kiebackpeter,imx6q-tpc", "fsl,imx6q";
> > +
> > + memory: memory@10000000 {
> > + reg = <0x10000000 0x40000000>;
> > + };
> > +};
> > +
> > +&ipu1_di0_disp0 {
> > + remote-endpoint = <&lcd_display_in>;
> > +};
> > diff --git a/arch/arm/boot/dts/imx6q-kp.dtsi
> > b/arch/arm/boot/dts/imx6q-kp.dtsi new file mode 100644
> > index 000000000000..acf6d40ca227
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-kp.dtsi
> > @@ -0,0 +1,460 @@
> > +/*
> > + * Copyright 2018
> > + * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/pwm/pwm.h>
> > +#include <dt-bindings/sound/fsl-imx-audmux.h>
> > +
> > +/ {
> > + backlight_lcd: backlight-lcd {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm1 0 5000000>;
> > + brightness-levels = < 0 1 2 3 4 5 6
> > 7 8 9
>
> There's a property now so you don't have to list every single value
> and can just say "<0 255>". It's not landed yet though. See
> "dt-bindings: pwm-backlight: add a num-interpolation-steps property".
According to the patch:
https://patchwork.kernel.org/patch/10205247/
This should be:
brightness-levels = <0 255>;
num-interpolation-steps = <255>;
>
> > + 10 11 12 13 14 15 16
> > 17 18 19
> > + 20 21 22 23 24 25 26
> > 27 28 29
> > + 30 31 32 33 34 35 36
> > 37 38 39
> > + 40 41 42 43 44 45 46
> > 47 48 49
> > + 50 51 52 53 54 55 56
> > 57 58 59
> > + 60 61 62 63 64 65 66
> > 67 68 69
> > + 70 71 72 73 74 75 76
> > 77 78 79
> > + 80 81 82 83 84 85 86
> > 87 88 89
> > + 90 91 92 93 94 95 96
> > 97 98 99
> > + 100 101 102 103 104 105 106
> > 107 108 109
> > + 110 111 112 113 114 115 116
> > 117 118 119
> > + 120 121 122 123 124 125 126
> > 127 128 129
> > + 130 131 132 133 134 135 136
> > 137 138 139
> > + 140 141 142 143 144 145 146
> > 147 148 149
> > + 150 151 152 153 154 155 156
> > 157 158 159
> > + 160 161 162 163 164 165 166
> > 167 168 169
> > + 170 171 172 173 174 175 176
> > 177 178 179
> > + 180 181 182 183 184 185 186
> > 187 188 189
> > + 190 191 192 193 194 195 196
> > 197 198 199
> > + 200 201 202 203 204 205 206
> > 207 208 209
> > + 210 211 212 213 214 215 216
> > 217 218 219
> > + 220 221 222 223 224 225 226
> > 227 228 229
> > + 230 231 232 233 234 235 236
> > 237 238 239
> > + 240 241 242 243 244 245 246
> > 247 248 249
> > + 250 251 252 253 254 255>;
> > + default-brightness-level = <250>;
> > + status = "okay";
>
> This isn't an existing node, so you don't need to override status.
Right. Non existent status equals to "okay".
>
> > + };
> > +
> > + beeper {
> > + compatible = "pwm-beeper";
> > + pwms = <&pwm2 0 500000>; //2kHz
> > + };
> > +
> > + lcd_display: disp0 {
> > + compatible = "fsl,imx-parallel-display";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + interface-pix-fmt = "rgb24";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ipu1>;
> > + status = "okay";
>
> Necessary?
I think that this can be removed.
>
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + lcd_display_in: endpoint {
> > + remote-endpoint =
> > <&ipu1_di0_disp0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + lcd_display_out: endpoint {
> > + remote-endpoint = <&lcd_panel_in>;
> > + };
> > + };
> > + };
> > +
> > + lcd_panel: lcd-panel {
> > + compatible = "auo,g070vvn01";
> > + backlight = <&backlight_lcd>;
> > + bus-format-override = "rgb565";
>
> This is not documented.
I've removed it in v4 of this patch. It is indeed not documented and
not needed.
>
> > + power-supply = <®_display>;
> > +
> > + port {
> > + lcd_panel_in: endpoint {
> > + remote-endpoint =
> > <&lcd_display_out>;
> > + };
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + green {
> > + label = "led1";
> > + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "gpio";
> > + default-state = "off";
> > + };
> > +
> > + red {
> > + label = "led0";
> > + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "gpio";
> > + default-state = "off";
> > + };
> > + };
> > +
> > + reg_3p3v: regulator-3p3v {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3P3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_audio: regulator-audio {
> > + compatible = "regulator-fixed";
> > + regulator-name = "sgtl5000-supply";
> > + gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + reg_display: regulator-display {
> > + compatible = "regulator-fixed";
> > + regulator-name = "display-supply";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_h1_vbus: regulator-usb_h1_vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_h1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + enable-active-high;
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "imx6q-sgtl5000-audio";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,bitclock-master = <&codec_dai>;
> > + simple-audio-card,frame-master = <&codec_dai>;
> > +
> > + cpu_dai: simple-audio-card,cpu {
> > + sound-dai = <&ssi1>;
> > + };
> > +
> > + codec_dai: simple-audio-card,codec {
> > + sound-dai = <&codec>;
> > + };
> > + };
> > +};
> > +
> > +&audmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_audmux>;
> > + status = "okay";
> > +
> > + ssi1 {
> > + fsl,audmux-port = <0>;
> > + fsl,port-config = <
> > + (IMX_AUDMUX_V2_PTCR_SYN |
> > + IMX_AUDMUX_V2_PTCR_TFSEL(2) |
> > + IMX_AUDMUX_V2_PTCR_TCSEL(2) |
> > + IMX_AUDMUX_V2_PTCR_TFSDIR |
> > + IMX_AUDMUX_V2_PTCR_TCLKDIR)
> > + IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> > + >;
> > + };
> > +
> > + aud3 {
> > + fsl,audmux-port = <2>;
> > + fsl,port-config = <
> > + IMX_AUDMUX_V2_PTCR_SYN
> > + IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> > + >;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + fsl,magic-packet;
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + goodix_ts@5d {
>
> touchscreen@5d
Ok.
>
> > + compatible = "goodix,gt911";
> > + reg = <0x5d>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ts>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> > + irq-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + rx8025@32 {
> > + compatible = "dallas,rx8025";
> > + reg = <0x32>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + codec: sgtl5000@a {
>
> audio-codec@a
Ok.
>
> > + compatible = "fsl,sgtl5000";
> > + #sound-dai-cells = <0>;
> > + reg = <0x0a>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_codec>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + VDDA-supply = <®_3p3v>;
> > + VDDIO-supply = <®_3p3v>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl_audmux: audmuxgrp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> > +
> > MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> > +
> > MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS
> > 0x130b0
> > + >;
> > + };
> > +
> > + pinctrl_codec: codecgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
> > + /* sgtl5000 sys_mclk clock routed to CLKO1
> > */
> > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO
> > 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> > + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> > + >;
> > + };
> > +
> > + pinctrl_flexcan1: can1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX
> > 0x1b0b0
> > + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX
> > 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_flexcan2: can2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX
> > 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA
> > 0x4001b8b1
> > + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL
> > 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL
> > 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA
> > 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_ipu1: ipu1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK
> > 0x10
> > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15
> > 0x10
> > + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02
> > 0x10
> > + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22
> > 0x10
> > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23
> > 0x10
> > + >;
> > + };
> > +
> > + pinctrl_pwm1: pwm1grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_pwm2: pwm2grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_ts: tsgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
> > + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA
> > 0x1b0b1
> > + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA
> > 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D26__UART2_TX_DATA
> > 0x1b0b1
> > + MX6QDL_PAD_EIM_D27__UART2_RX_DATA
> > 0x1b0b1
> > + MX6QDL_PAD_EIM_D28__UART2_CTS_B
> > 0x1b0b1
> > + MX6QDL_PAD_EIM_D29__UART2_RTS_B
> > 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD
> > 0x17059
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK
> > 0x10059
> > +
> > MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc4: usdhc4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_CMD__SD4_CMD
> > 0x17059
> > + MX6QDL_PAD_SD4_CLK__SD4_CLK
> > 0x10059
> > +
> > MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
> > +
> > MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
> > + >;
> > + };
> > +};
> > +
> > +&can1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_flexcan1>;
> > +};
> > +
> > +&can2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_flexcan2>;
> > +};
> > +
> > +&pwm1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm1>;
> > + status = "okay";
> > +};
> > +
> > +&pwm2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm2>;
> > + status = "okay";
> > +};
> > +
> > +&ssi1 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + uart-has-rtscts;
> > +};
> > +
> > +&usbh1 {
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc4>;
> > + bus-width = <8>;
> > + non-removable;
> > + no-1-8-v;
> > + keep-power-in-suspend;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + status = "okay";
> > +};
> > --
> > 2.11.0
> >
Thanks for your review.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@xxxxxxx
Attachment:
pgpYDnGFF7i9g.pgp
Description: OpenPGP digital signature