Re: [PATCH v2 5/5] DTS: Bindings: pca953x: add example how to use interrupt-controller and gpio-controller

[H. Nikolaus Schaller]

> Am 10.04.2018 um 15:57 schrieb Rob Herring <robh@xxxxxxxxxx>:
> 
> On Wed, Apr 04, 2018 at 09:00:24PM +0200, H. Nikolaus Schaller wrote:
>> It is not completely obvious that these are required as
>> some .dts files don't specify them.
>> 
>> Signed-off-by: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>
>> ---
>> .../devicetree/bindings/gpio/gpio-pca953x.txt      | 33 ++++++++++++++++++++++
>> 1 file changed, 33 insertions(+)
>> 
>> diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
>> index 6a7cddb187c1..7f3b50a6d681 100644
>> --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
>> +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
>> @@ -36,6 +36,10 @@ Optional properties:
>>  - reset-gpios: GPIO specification for the RESET input. This is an
>> 		active low signal to the PCA953x.
>>  - vcc-supply:	power supply regulator.
>> + - gpio-controller: if used as gpio expander.
>> + - #gpio-cells: if used as gpio expander.
>> + - interrupt-controller: if to be used as interrupt expander.
>> + - #interrupt-cells: if to be used as interrupt expander.
> 
> These should be required. It's a mistake if dts files don't have them.

Well, it seems to be a config option if the chip handles interrupts
at all, but I also tend to say they are required.

> 
>> 
>> Example:
>> 
>> @@ -48,3 +52,32 @@ Example:
>> 		interrupt-parent = <&gpio3>;
>> 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
>> 	};
>> +
>> +
>> +Example with Interrupts:
>> +
>> +
>> +	gpio99: tca6424@22 {
> 
> gpio@22

Ok!

> 
>> +		compatible = "nxp,pcal6524";
>> +		reg = <0x22>;
>> +		interrupt-parent = <&gpio6>;
>> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;	/* gpio6_161 */
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +		vcc-supply = <&vdds_1v8_main>;
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +		gpio-line-names =
>> +			"hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07",
>> +			"en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem",
>> +			"shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27";
>> +	};
>> +
>> +	ts3a227@3b {
>> +		compatible = "ti,ts3a227e";
>> +		reg = <0x3b>;
>> +		interrupt-parent = <&gpio99>;
>> +		interrupts = <14 IRQ_TYPE_EDGE_RISING>;
>> +		ti,micbias = <0>;	/* 2.1V */
>> +	};
>> +
>> -- 
>> 2.12.2
>> 

BR and thanks,
Nikolaus