Re: [PATCH v3] gpio: dwapb: Add support for 1 interrupt per port A GPIO

[Hoan Tran]

Hi Phil,

On Thu, Apr 19, 2018 at 3:03 AM, Phil Edworthy
<phil.edworthy@xxxxxxxxxxx> wrote:
> Hi Hoan
>
> On 18 April 2018 08:03 Hoan Tran wrote:
>> On Fri, Apr 13, 2018 at 9:47 AM, Phil Edworthy wrote:
>> > On 13 April 2018 17:37 Hoan Tran wrote:
>> >> On Fri, Apr 13, 2018 at 1:51 AM, Phil Edworthy wrote:
>> >> > The DesignWare GPIO IP can be configured for either 1 interrupt or
>> >> > 1 per GPIO in port A, but the driver currently only supports 1 interrupt.
>> >> > See the DesignWare DW_apb_gpio Databook description of the
>> >> > 'GPIO_INTR_IO' parameter.
>> >> >
>> >> > This change allows the driver to work with up to 32 interrupts, it
>> >> > will get as many interrupts as specified in the DT 'interrupts' property.
>> >> > It doesn't do anything clever with the different interrupts, it
>> >> > just calls the same handler used for single interrupt hardware.
>> >> >
>> >> > Signed-off-by: Phil Edworthy <phil.edworthy@xxxxxxxxxxx>
>> >> > ---
>> >> > One point to mention is that I have made it possible for users to
>> >> > have unconncted interrupts by specifying holes in the list of interrupts.
>> >> > This is done by supporting the interrupts-extended DT prop.
>> >> > However, I have no use for this and had to hack some test case for this.
>> >> > Perhaps the driver should support 1 interrupt or all GPIOa as interrupts?
>> >> >
>> >> > v3:
>> >> >  - Rolled mfd: intel_quark_i2c_gpio fix into this patch to avoid
>> >> > bisect problems
>> >> > v2:
>> >> >  - Replaced interrupt-mask DT prop with support for the interrupts-
>> >> extended
>> >> >    prop. This means replacing the call to irq_of_parse_and_map() with
>> calls
>> >> >    to of_irq_parse_one() and irq_create_of_mapping().
>> >> >
>> >> > Note: There are a few *code* lines over 80 chars, but this is just
>> guidance,
>> >> >    right? Especially as there are already some lines over 80 chars.
>> >> > ---
>> > [snip]
>> >
>> >> > -               if (has_acpi_companion(dev) && pp->idx == 0)
>> >> > -                       pp->irq = platform_get_irq(to_platform_device(dev), 0);
>> >> > +               if (has_acpi_companion(dev) && pp->idx == 0) {
>> >> > +                       pp->irq[0] = platform_get_irq(to_platform_device(dev),
>> 0);
>> >> > +                       if (pp->irq[0])
>> >> > +                               pp->has_irq = true;
>> >> > +               }
>> >>
>> >> It doesn't work for ACPI. Could you do the same logic for ACPI?
>> > I donât have access to any device that was baked (i.e. fabbed) with
>> > multiple output interrupts from the Synopsys GPIO blocks and use ACPI.
>> > I don't know if any such device exists.
>>
>> Below code is tested on X-Gene system which supports 1 interrupt per GPIO
>> on Port A. You can update it into your patch.
>>
>> -               if (has_acpi_companion(dev) && pp->idx == 0)
>> -                       pp->irq = platform_get_irq(to_platform_device(dev), 0);
>> +               if (has_acpi_companion(dev) && pp->idx == 0) {
>> +                       unsigned int j;
>> +                       for (j = 0; j < pp->ngpio; j++) {
>> +                               pp->irq[j] =
>> platform_get_irq(to_platform_device(dev), j);
>> +                               if (pp->irq[j])
>> +                                       pp->has_irq = true;
>> +                       }
>> +               }
> Since I've already got some reviewed-by and acks for v4, I'll leave it to Linus
> to decide if he wants me to roll your changes into this patch or for you to
> submit a separate patch.
>

I prefer this patch works for both DTB and ACPI. Btw let Linus decide.

Thanks
Hoan

> Thanks
> Phil
>
>
>> >> >                 pp->irq_shared  = false;
>> >> >                 pp->gpio_base   = -1;
>> >> > diff --git a/drivers/mfd/intel_quark_i2c_gpio.c
>> >> > b/drivers/mfd/intel_quark_i2c_gpio.c
>> >> > index 90e35de..5bddb84 100644
>> >> > --- a/drivers/mfd/intel_quark_i2c_gpio.c
>> >> > +++ b/drivers/mfd/intel_quark_i2c_gpio.c
>> >> > @@ -233,7 +233,8 @@ static int intel_quark_gpio_setup(struct
>> >> > pci_dev
>> >> *pdev, struct mfd_cell *cell)
>> >> >         pdata->properties->idx          = 0;
>> >> >         pdata->properties->ngpio        = INTEL_QUARK_MFD_NGPIO;
>> >> >         pdata->properties->gpio_base    =
>> INTEL_QUARK_MFD_GPIO_BASE;
>> >> > -       pdata->properties->irq          = pdev->irq;
>> >> > +       pdata->properties->irq[0]       = pdev->irq;
>> >> > +       pdata->properties->has_irq      = true;
>> >> >         pdata->properties->irq_shared   = true;
>> >> >
>> >> >         cell->platform_data = pdata; diff --git
>> >> > a/include/linux/platform_data/gpio-dwapb.h
>> >> > b/include/linux/platform_data/gpio-dwapb.h
>> >> > index 2dc7f4a..5a52d69 100644
>> >> > --- a/include/linux/platform_data/gpio-dwapb.h
>> >> > +++ b/include/linux/platform_data/gpio-dwapb.h
>> >> > @@ -19,7 +19,8 @@ struct dwapb_port_property {
>> >> >         unsigned int    idx;
>> >> >         unsigned int    ngpio;
>> >> >         unsigned int    gpio_base;
>> >> > -       unsigned int    irq;
>> >> > +       unsigned int    irq[32];
>> >> > +       bool            has_irq;
>> >> >         bool            irq_shared;
>> >> >  };
>> >> >
>> >> > --
>> >> > 2.7.4
>> >> >