Re: [PATCH 1/2] cpufreq: brcmstb-avs-cpufreq: remove development debug support

From: Rafael J. Wysocki
Date: Mon Apr 30 2018 - 04:26:53 EST


On Wednesday, April 18, 2018 5:56:42 PM CEST Markus Mayer wrote:
> From: Markus Mayer <mmayer@xxxxxxxxxxxx>
>
> This debug code was helpful while developing the driver, but it isn't
> being used for anything anymore.
>
> Signed-off-by: Markus Mayer <mmayer@xxxxxxxxxxxx>
> ---
> drivers/cpufreq/Kconfig.arm | 10 --
> drivers/cpufreq/brcmstb-avs-cpufreq.c | 323 +---------------------------------
> 2 files changed, 1 insertion(+), 332 deletions(-)
>
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 7f56fe5183f2..de55c7d57438 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -71,16 +71,6 @@ config ARM_BRCMSTB_AVS_CPUFREQ
>
> Say Y, if you have a Broadcom SoC with AVS support for DFS or DVFS.
>
> -config ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> - bool "Broadcom STB AVS CPUfreq driver sysfs debug capability"
> - depends on ARM_BRCMSTB_AVS_CPUFREQ
> - help
> - Enabling this option turns on debug support via sysfs under
> - /sys/kernel/debug/brcmstb-avs-cpufreq. It is possible to read all and
> - write some AVS mailbox registers through sysfs entries.
> -
> - If in doubt, say N.
> -
> config ARM_EXYNOS5440_CPUFREQ
> tristate "SAMSUNG EXYNOS5440"
> depends on SOC_EXYNOS5440
> diff --git a/drivers/cpufreq/brcmstb-avs-cpufreq.c b/drivers/cpufreq/brcmstb-avs-cpufreq.c
> index 6cdac1aaf23c..b07559b9ed99 100644
> --- a/drivers/cpufreq/brcmstb-avs-cpufreq.c
> +++ b/drivers/cpufreq/brcmstb-avs-cpufreq.c
> @@ -49,13 +49,6 @@
> #include <linux/platform_device.h>
> #include <linux/semaphore.h>
>
> -#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> -#include <linux/ctype.h>
> -#include <linux/debugfs.h>
> -#include <linux/slab.h>
> -#include <linux/uaccess.h>
> -#endif
> -
> /* Max number of arguments AVS calls take */
> #define AVS_MAX_CMD_ARGS 4
> /*
> @@ -182,88 +175,11 @@ struct private_data {
> void __iomem *base;
> void __iomem *avs_intr_base;
> struct device *dev;
> -#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> - struct dentry *debugfs;
> -#endif
> struct completion done;
> struct semaphore sem;
> struct pmap pmap;
> };
>
> -#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> -
> -enum debugfs_format {
> - DEBUGFS_NORMAL,
> - DEBUGFS_FLOAT,
> - DEBUGFS_REV,
> -};
> -
> -struct debugfs_data {
> - struct debugfs_entry *entry;
> - struct private_data *priv;
> -};
> -
> -struct debugfs_entry {
> - char *name;
> - u32 offset;
> - fmode_t mode;
> - enum debugfs_format format;
> -};
> -
> -#define DEBUGFS_ENTRY(name, mode, format) { \
> - #name, AVS_MBOX_##name, mode, format \
> -}
> -
> -/*
> - * These are used for debugfs only. Otherwise we use AVS_MBOX_PARAM() directly.
> - */
> -#define AVS_MBOX_PARAM1 AVS_MBOX_PARAM(0)
> -#define AVS_MBOX_PARAM2 AVS_MBOX_PARAM(1)
> -#define AVS_MBOX_PARAM3 AVS_MBOX_PARAM(2)
> -#define AVS_MBOX_PARAM4 AVS_MBOX_PARAM(3)
> -
> -/*
> - * This table stores the name, access permissions and offset for each hardware
> - * register and is used to generate debugfs entries.
> - */
> -static struct debugfs_entry debugfs_entries[] = {
> - DEBUGFS_ENTRY(COMMAND, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(STATUS, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(VOLTAGE0, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(TEMP0, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(PV0, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(MV0, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(PARAM1, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(PARAM2, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(PARAM3, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(PARAM4, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(REVISION, 0, DEBUGFS_REV),
> - DEBUGFS_ENTRY(PSTATE, 0, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(HEARTBEAT, 0, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(MAGIC, S_IWUSR, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(SIGMA_HVT, 0, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(SIGMA_SVT, 0, DEBUGFS_NORMAL),
> - DEBUGFS_ENTRY(VOLTAGE1, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(TEMP1, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(PV1, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(MV1, 0, DEBUGFS_FLOAT),
> - DEBUGFS_ENTRY(FREQUENCY, 0, DEBUGFS_NORMAL),
> -};
> -
> -static int brcm_avs_target_index(struct cpufreq_policy *, unsigned int);
> -
> -static char *__strtolower(char *s)
> -{
> - char *p;
> -
> - for (p = s; *p; p++)
> - *p = tolower(*p);
> -
> - return s;
> -}
> -
> -#endif /* CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG */
> -
> static void __iomem *__map_region(const char *name)
> {
> struct device_node *np;
> @@ -516,238 +432,6 @@ brcm_avs_get_freq_table(struct device *dev, struct private_data *priv)
> return table;
> }
>
> -#ifdef CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG
> -
> -#define MANT(x) (unsigned int)(abs((x)) / 1000)
> -#define FRAC(x) (unsigned int)(abs((x)) - abs((x)) / 1000 * 1000)
> -
> -static int brcm_avs_debug_show(struct seq_file *s, void *data)
> -{
> - struct debugfs_data *dbgfs = s->private;
> - void __iomem *base;
> - u32 val, offset;
> -
> - if (!dbgfs) {
> - seq_puts(s, "No device pointer\n");
> - return 0;
> - }
> -
> - base = dbgfs->priv->base;
> - offset = dbgfs->entry->offset;
> - val = readl(base + offset);
> - switch (dbgfs->entry->format) {
> - case DEBUGFS_NORMAL:
> - seq_printf(s, "%u\n", val);
> - break;
> - case DEBUGFS_FLOAT:
> - seq_printf(s, "%d.%03d\n", MANT(val), FRAC(val));
> - break;
> - case DEBUGFS_REV:
> - seq_printf(s, "%c.%c.%c.%c\n", (val >> 24 & 0xff),
> - (val >> 16 & 0xff), (val >> 8 & 0xff),
> - val & 0xff);
> - break;
> - }
> - seq_printf(s, "0x%08x\n", val);
> -
> - return 0;
> -}
> -
> -#undef MANT
> -#undef FRAC
> -
> -static ssize_t brcm_avs_seq_write(struct file *file, const char __user *buf,
> - size_t size, loff_t *ppos)
> -{
> - struct seq_file *s = file->private_data;
> - struct debugfs_data *dbgfs = s->private;
> - struct private_data *priv = dbgfs->priv;
> - void __iomem *base, *avs_intr_base;
> - bool use_issue_command = false;
> - unsigned long val, offset;
> - char str[128];
> - int ret;
> - char *str_ptr = str;
> -
> - if (size >= sizeof(str))
> - return -E2BIG;
> -
> - memset(str, 0, sizeof(str));
> - ret = copy_from_user(str, buf, size);
> - if (ret)
> - return ret;
> -
> - base = priv->base;
> - avs_intr_base = priv->avs_intr_base;
> - offset = dbgfs->entry->offset;
> - /*
> - * Special case writing to "command" entry only: if the string starts
> - * with a 'c', we use the driver's __issue_avs_command() function.
> - * Otherwise, we perform a raw write. This should allow testing of raw
> - * access as well as using the higher level function. (Raw access
> - * doesn't clear the firmware return status after issuing the command.)
> - */
> - if (str_ptr[0] == 'c' && offset == AVS_MBOX_COMMAND) {
> - use_issue_command = true;
> - str_ptr++;
> - }
> - if (kstrtoul(str_ptr, 0, &val) != 0)
> - return -EINVAL;
> -
> - /*
> - * Setting the P-state is a special case. We need to update the CPU
> - * frequency we report.
> - */
> - if (val == AVS_CMD_SET_PSTATE) {
> - struct cpufreq_policy *policy;
> - unsigned int pstate;
> -
> - policy = cpufreq_cpu_get(smp_processor_id());
> - /* Read back the P-state we are about to set */
> - pstate = readl(base + AVS_MBOX_PARAM(0));
> - if (use_issue_command) {
> - ret = brcm_avs_target_index(policy, pstate);
> - return ret ? ret : size;
> - }
> - policy->cur = policy->freq_table[pstate].frequency;
> - }
> -
> - if (use_issue_command) {
> - ret = __issue_avs_command(priv, val, false, NULL);
> - } else {
> - /* Locking here is not perfect, but is only for debug. */
> - ret = down_interruptible(&priv->sem);
> - if (ret)
> - return ret;
> -
> - writel(val, base + offset);
> - /* We have to wake up the firmware to process a command. */
> - if (offset == AVS_MBOX_COMMAND)
> - writel(AVS_CPU_L2_INT_MASK,
> - avs_intr_base + AVS_CPU_L2_SET0);
> - up(&priv->sem);
> - }
> -
> - return ret ? ret : size;
> -}
> -
> -static struct debugfs_entry *__find_debugfs_entry(const char *name)
> -{
> - int i;
> -
> - for (i = 0; i < ARRAY_SIZE(debugfs_entries); i++)
> - if (strcasecmp(debugfs_entries[i].name, name) == 0)
> - return &debugfs_entries[i];
> -
> - return NULL;
> -}
> -
> -static int brcm_avs_debug_open(struct inode *inode, struct file *file)
> -{
> - struct debugfs_data *data;
> - fmode_t fmode;
> - int ret;
> -
> - /*
> - * seq_open(), which is called by single_open(), clears "write" access.
> - * We need write access to some files, so we preserve our access mode
> - * and restore it.
> - */
> - fmode = file->f_mode;
> - /*
> - * Check access permissions even for root. We don't want to be writing
> - * to read-only registers. Access for regular users has already been
> - * checked by the VFS layer.
> - */
> - if ((fmode & FMODE_WRITER) && !(inode->i_mode & S_IWUSR))
> - return -EACCES;
> -
> - data = kmalloc(sizeof(*data), GFP_KERNEL);
> - if (!data)
> - return -ENOMEM;
> - /*
> - * We use the same file system operations for all our debug files. To
> - * produce specific output, we look up the file name upon opening a
> - * debugfs entry and map it to a memory offset. This offset is then used
> - * in the generic "show" function to read a specific register.
> - */
> - data->entry = __find_debugfs_entry(file->f_path.dentry->d_iname);
> - data->priv = inode->i_private;
> -
> - ret = single_open(file, brcm_avs_debug_show, data);
> - if (ret)
> - kfree(data);
> - file->f_mode = fmode;
> -
> - return ret;
> -}
> -
> -static int brcm_avs_debug_release(struct inode *inode, struct file *file)
> -{
> - struct seq_file *seq_priv = file->private_data;
> - struct debugfs_data *data = seq_priv->private;
> -
> - kfree(data);
> - return single_release(inode, file);
> -}
> -
> -static const struct file_operations brcm_avs_debug_ops = {
> - .open = brcm_avs_debug_open,
> - .read = seq_read,
> - .write = brcm_avs_seq_write,
> - .llseek = seq_lseek,
> - .release = brcm_avs_debug_release,
> -};
> -
> -static void brcm_avs_cpufreq_debug_init(struct platform_device *pdev)
> -{
> - struct private_data *priv = platform_get_drvdata(pdev);
> - struct dentry *dir;
> - int i;
> -
> - if (!priv)
> - return;
> -
> - dir = debugfs_create_dir(BRCM_AVS_CPUFREQ_NAME, NULL);
> - if (IS_ERR_OR_NULL(dir))
> - return;
> - priv->debugfs = dir;
> -
> - for (i = 0; i < ARRAY_SIZE(debugfs_entries); i++) {
> - /*
> - * The DEBUGFS_ENTRY macro generates uppercase strings. We
> - * convert them to lowercase before creating the debugfs
> - * entries.
> - */
> - char *entry = __strtolower(debugfs_entries[i].name);
> - fmode_t mode = debugfs_entries[i].mode;
> -
> - if (!debugfs_create_file(entry, S_IFREG | S_IRUGO | mode,
> - dir, priv, &brcm_avs_debug_ops)) {
> - priv->debugfs = NULL;
> - debugfs_remove_recursive(dir);
> - break;
> - }
> - }
> -}
> -
> -static void brcm_avs_cpufreq_debug_exit(struct platform_device *pdev)
> -{
> - struct private_data *priv = platform_get_drvdata(pdev);
> -
> - if (priv && priv->debugfs) {
> - debugfs_remove_recursive(priv->debugfs);
> - priv->debugfs = NULL;
> - }
> -}
> -
> -#else
> -
> -static void brcm_avs_cpufreq_debug_init(struct platform_device *pdev) {}
> -static void brcm_avs_cpufreq_debug_exit(struct platform_device *pdev) {}
> -
> -#endif /* CONFIG_ARM_BRCMSTB_AVS_CPUFREQ_DEBUG */
> -
> /*
> * To ensure the right firmware is running we need to
> * - check the MAGIC matches what we expect
> @@ -1016,11 +700,8 @@ static int brcm_avs_cpufreq_probe(struct platform_device *pdev)
> return ret;
>
> brcm_avs_driver.driver_data = pdev;
> - ret = cpufreq_register_driver(&brcm_avs_driver);
> - if (!ret)
> - brcm_avs_cpufreq_debug_init(pdev);
>
> - return ret;
> + return cpufreq_register_driver(&brcm_avs_driver);
> }
>
> static int brcm_avs_cpufreq_remove(struct platform_device *pdev)
> @@ -1032,8 +713,6 @@ static int brcm_avs_cpufreq_remove(struct platform_device *pdev)
> if (ret)
> return ret;
>
> - brcm_avs_cpufreq_debug_exit(pdev);
> -
> priv = platform_get_drvdata(pdev);
> iounmap(priv->base);
> iounmap(priv->avs_intr_base);
>

Applied and merged into 4.17-rc3, thanks!