Re: [PATCH 10/28] venus: vdec: call session_continue in insufficient event

From: Vikash Garodia
Date: Fri May 04 2018 - 07:10:06 EST


Hi Stanimir,

On 2018-05-03 17:06, Stanimir Varbanov wrote:
Hi Vikash,

Thanks for the comments!

On 2.05.2018 09:26, Vikash Garodia wrote:
Hello Stanimir,

On 2018-04-24 18:14, Stanimir Varbanov wrote:
Call session_continue for Venus 4xx version even when the event
says that the buffer resources are not sufficient. Leaving a
comment with more information about the workaround.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@xxxxxxxxxx>
---
Âdrivers/media/platform/qcom/venus/vdec.c | 8 ++++++++
Â1 file changed, 8 insertions(+)

diff --git a/drivers/media/platform/qcom/venus/vdec.c
b/drivers/media/platform/qcom/venus/vdec.c
index c45452634e7e..91c7384ff9c8 100644
--- a/drivers/media/platform/qcom/venus/vdec.c
+++ b/drivers/media/platform/qcom/venus/vdec.c
@@ -873,6 +873,14 @@ static void vdec_event_notify(struct venus_inst
*inst, u32 event,

ÂÂÂÂÂÂÂÂÂÂÂÂ dev_dbg(dev, "event not sufficient resources (%ux%u)\n",
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ data->width, data->height);
+ÂÂÂÂÂÂÂÂÂÂÂ /*
+ÂÂÂÂÂÂÂÂÂÂÂÂ * Workaround: Even that the firmware send and event for
+ÂÂÂÂÂÂÂÂÂÂÂÂ * insufficient buffer resources it is safe to call
+ÂÂÂÂÂÂÂÂÂÂÂÂ * session_continue because actually the event says that
+ÂÂÂÂÂÂÂÂÂÂÂÂ * the number of capture buffers is lower.
+ÂÂÂÂÂÂÂÂÂÂÂÂ */
+ÂÂÂÂÂÂÂÂÂÂÂ if (IS_V4(core))
+ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ hfi_session_continue(inst);
ÂÂÂÂÂÂÂÂÂÂÂÂ break;
ÂÂÂÂÂÂÂÂ case HFI_EVENT_RELEASE_BUFFER_REFERENCE:
ÂÂÂÂÂÂÂÂÂÂÂÂ venus_helper_release_buf_ref(inst, data->tag);

Insufficient event from video firmware could be sent either,
1. due to insufficient buffer resources
2. due to lower capture buffers

It cannot be assumed that the event received by the host is due to lower capture
buffers. Incase the buffer resource is insufficient, let say there is a bitstream
resolution switch from 720p to 1080p, capture buffers needs to be reallocated.

I agree with you. I will rework this part and call session_continue
only for case #2.

Even if the capture buffers are lower, driver should consider reallocation of capture
buffers with required higher count. Without this, it may happen that for a given video
frame, the decoded output will not be generated. The fact that the DPB buffer count is
same as capture buffers, will be lower than required. Hence the frame which needs YUV
reference beyond the DPB count, will get stuck as it cannot be decoded due to unavailability
of sufficient DPB buffers.
Say for ex. 10 DPB and capture buffers are allocated. For a given bitstream, firmware requested
the count to be 15. Frame 1 to 10 gets decoded and stored in DPB as references for future frame
decoding. Now when the 11th frame is queued to firmware, it can be decode but cannot be stored
as reference to decode future (12th) frame. Hence 11 frame will get stuck and will not be given
back to host driver.


The driver should be sending the V4L2_EVENT_SOURCE_CHANGE to client instead of ignoring
the event from firmware.

The v4l2 event is sent always to v4l clients.

regards,
Stan