[PATCH 3/3] ARM: dts: sun7i: Add support for the Ainol AW1 tablet
From: Paul Kocialkowski
Date: Sun May 06 2018 - 16:57:31 EST
This adds support for the Ainol AW1, an A20-based 7" tablet from Ainol.
The following board-specific features are supported:
* LCD panel
* Backlight
* USB OTG
* Buttons
* Touchscreen (doesn't work without non-free firmware)
* Accelerometer
* Battery
The following are untested:
* Audio output
* Audio speakers
* USB via SPCI connector
The following are not supported:
* Wi-Fi
* Bluetooth
* NAND
* Audio via SPCI connector
* Audio via Bluetooth I2S
Signed-off-by: Paul Kocialkowski <contact@xxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts | 275 ++++++++++++++++++++++
2 files changed, 276 insertions(+)
create mode 100644 arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e2424957809..4a80971f2bc9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -946,6 +946,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31s-sinovoip-bpi-m2.dtb \
sun6i-a31s-yones-toptech-bs1078-v2.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
+ sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapi-m1-plus.dtb \
sun7i-a20-bananapro.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
new file mode 100644
index 000000000000..6bb7f47fd010
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
@@ -0,0 +1,275 @@
+/*
+ * Copyright (C) 2018 Paul Kocialkowski <contact@xxxxxxxx>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Ainol AW1";
+ compatible = "ainol,ainol-aw1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <5>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
+ panel: panel {
+ compatible = "innolux,at070tn90";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-supply = <&panel_power>;
+ backlight = <&backlight>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+
+ panel_power: panel_power {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_power_pin>;
+ regulator-name = "panel-power";
+ regulator-min-microvolt = <10400000>;
+ regulator-max-microvolt = <10400000>;
+ gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ enable-active-high;
+ regulator-boot-on;
+ };
+};
+
+&codec {
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ lis3dh: accelerometer@18 {
+ compatible = "st,lis3dh-accel";
+ reg = <0x18>;
+ vdd-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ st,drdy-int-pin = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ gsl1680: touchscreen@40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+ power-gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ firmware-name = "gsl1680-ainol-aw1.fw";
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+ touchscreen-swapped-x-y;
+ touchscreen-inverted-y;
+ silead,max-fingers = <5>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button@571 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <571428>;
+ };
+
+ button@761 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <761904>;
+ };
+
+ button@952 {
+ label = "Home";
+ linux,code = <KEY_HOME>;
+ channel = <0>;
+ voltage = <952380>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ panel_power_pin: panel_power_pin@0 {
+ pins = "PH8";
+ function = "gpio_out";
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd0_rgb888_pins>;
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&battery_power_supply {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
--
2.17.0