Re: [PATCH v2 01/14] mtd: rawnand: helper function for setting up ECC parameters
From: Masahiro Yamada
Date: Sun May 06 2018 - 23:41:50 EST
2018-05-03 21:20 GMT+09:00 Abhishek Sahu <absahu@xxxxxxxxxxxxxx>:
> commit 2c8f8afa7f92 ("mtd: nand: add generic helpers to check,
> match, maximize ECC settings") provides generic helpers which
> drivers can use for setting up ECC parameters.
>
> Since same board can have different ECC strength nand chips so
> following is the logic for setting up ECC strength and ECC step
> size, which can be used by most of the drivers.
>
> 1. If both ECC step size and ECC strength are already set
> (usually by DT) then just check whether this setting
> is supported by NAND controller.
> 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
> supported by NAND controller.
> 3. Otherwise, try to match the ECC step size and ECC strength closest
> to the chip's requirement. If available OOB size can't fit the chip
> requirement then select maximum ECC strength which can be fit with
> available OOB size with warning.
>
> This patch introduces nand_ecc_param_setup function which calls the
> required helper functions for the above logic. The drivers can use
> this single function instead of calling the 3 helper functions
> individually.
>
> CC: Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx>
> Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
> ---
> * Changes from v1:
>
> NEW PATCH
>
> drivers/mtd/nand/raw/nand_base.c | 42 ++++++++++++++++++++++++++++++++++++++++
> include/linux/mtd/rawnand.h | 3 +++
> 2 files changed, 45 insertions(+)
>
> diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
> index 72f3a89..dd7a984 100644
> --- a/drivers/mtd/nand/raw/nand_base.c
> +++ b/drivers/mtd/nand/raw/nand_base.c
> @@ -6249,6 +6249,48 @@ int nand_maximize_ecc(struct nand_chip *chip,
> }
> EXPORT_SYMBOL_GPL(nand_maximize_ecc);
>
> +/**
> + * nand_ecc_param_setup - Set the ECC strength and ECC step size
> + * @chip: nand chip info structure
> + * @caps: ECC engine caps info structure
> + * @oobavail: OOB size that the ECC engine can use
> + *
> + * Choose the ECC strength according to following logic
> + *
> + * 1. If both ECC step size and ECC strength are already set (usually by DT)
> + * then check if it is supported by this controller.
> + * 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength.
> + * 3. Otherwise, try to match the ECC step size and ECC strength closest
> + * to the chip's requirement. If available OOB size can't fit the chip
> + * requirement then fallback to the maximum ECC step size and ECC strength
> + * and print the warning.
> + *
> + * On success, the chosen ECC settings are set.
> + */
> +int nand_ecc_param_setup(struct nand_chip *chip,
> + const struct nand_ecc_caps *caps, int oobavail)
> +{
> + int ret;
> +
> + if (chip->ecc.size && chip->ecc.strength)
> + return nand_check_ecc_caps(chip, caps, oobavail);
> +
> + if (chip->ecc.options & NAND_ECC_MAXIMIZE)
> + return nand_maximize_ecc(chip, caps, oobavail);
> +
> + if (!nand_match_ecc_req(chip, caps, oobavail))
> + return 0;
> +
> + ret = nand_maximize_ecc(chip, caps, oobavail);
Why two calls for nand_maximize_ecc()?
My code is simpler, and does not display
false-positive warning.
> + if (!ret)
> + pr_warn("ECC (step, strength) = (%d, %d) not supported on this controller. Fallback to (%d, %d)\n",
> + chip->ecc_step_ds, chip->ecc_strength_ds,
> + chip->ecc.size, chip->ecc.strength);
This is annoying.
{ecc_step_ds, ecc_strength_ds} are not provided by Non-ONFi devices.
So,
ECC (step, strength) = (0, 0) not supported on this controller.
will be always displayed.
The strength will be checked by nand_ecc_strength_good() anyway.
> +
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(nand_ecc_param_setup);
--
Best Regards
Masahiro Yamada