[PATCH v0 2/2] arm64: dts: rockchip: Add sdmmc UHS support for roc-rk3328-cc

From: djw
Date: Mon May 07 2018 - 22:49:51 EST


From: Levin Du <djw@xxxxxxxxxxxxx>

In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by
the vcc_sdio regulator, which is a mux between 1.8V and 3.3V,
controlled by a special output only gpio pin.

However, this pin, not being a normal gpio in the rockchip pinctrl,
is set by bit 1 of system register GRF_SOC_CON10. Therefore a new
gpio controller using gpio-syscon driver is defined in order to use
regulator-gpio.

If the signal voltage changes, the io domain needs to change
correspondingly.

To use this feature, the following options are required in kernel config:
- CONFIG_GPIO_SYSCON=y
- CONFIG_POWER_AVS=y
- CONFIG_ROCKCHIP_IODOMAIN=y

Signed-off-by: Levin Du <djw@xxxxxxxxxxxxx>

---

arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts | 36 ++++++++++++++++++++++++++
1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
index 246c317..792cb04 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -14,6 +14,12 @@
stdout-path = "serial2:1500000n8";
};

+ gpio_syscon10: gpio-syscon10 {
+ compatible = "rockchip,rk3328-gpio-syscon10";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
gmac_clkin: external-gmac-clock {
compatible = "fixed-clock";
clock-frequency = <125000000>;
@@ -41,6 +47,19 @@
vin-supply = <&vcc_io>;
};

+ vcc_sdio: sdmmcio-regulator {
+ compatible = "regulator-gpio";
+ gpios = <&gpio_syscon10 1 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ regulator-name = "vcc_sdio";
+ regulator-type = "voltage";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
compatible = "regulator-fixed";
enable-active-high;
@@ -208,6 +227,18 @@
};
};

+&io_domains {
+ status = "okay";
+
+ vccio1-supply = <&vcc_io>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_sdio>;
+ vccio4-supply = <&vcc_18>;
+ vccio5-supply = <&vcc_io>;
+ vccio6-supply = <&vcc_io>;
+ pmuio-supply = <&vcc_io>;
+};
+
&pinctrl {
pmic {
pmic_int_l: pmic-int-l {
@@ -227,10 +258,15 @@
cap-mmc-highspeed;
cap-sd-highspeed;
disable-wp;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
max-frequency = <150000000>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vcc_sdio>;
status = "okay";
};

--
2.7.4