Re: [PATCH 1/5] dt-bindings: pinctrl: document the STMFX pinctrl bindings

[Amelie DELAUNAY]

On 05/24/2018 09:13 AM, Linus Walleij wrote:
> On Fri, May 18, 2018 at 9:29 AM, Amelie DELAUNAY <amelie.delaunay@xxxxxx> wrote:
>> On 05/17/2018 08:36 AM, Lee Jones wrote:
>>> On Wed, 16 May 2018, Amelie DELAUNAY wrote:
>>>> On 05/16/2018 04:20 PM, Linus Walleij wrote:
>>>>> On Wed, May 9, 2018 at 9:56 AM, Amelie DELAUNAY <amelie.delaunay@xxxxxx> wrote:
>>>>>
>>>>>> Indeed, stmfx has other functions than GPIO. But, after comments done
>>>>>> here: [1] and there: [2], it has been decided to move MFD parent/GPIO
>>>>>> child drivers into a single PINCTRL/GPIO driver because of the following
>>>>>> reasons:
>>>>>> - Other stmfx functions (IDD measurement and TouchScreen controller) are
>>>>>> not used on any of the boards using an stmfx and supported by Linux, so
>>>>>> no way to test these functions, and no need to maintain them while they
>>>>>> are not being used.
>>>>>> - But, in the case a new board will use more than GPIO function on
>>>>>> stmfx, the actual implementation allow to easily extract common init
>>>>>> part of stmfx and put it in an MFD driver.
>>>>>>
>>>>>> So I could remove gpio sub-node and put its contents in stmfx node and
>>>>>> keep single PINCTRL/GPIO driver for the time being.
>>>>>> Please advise,
>>>>>
>>>>> I would normally advice to use the right modeling from the start, create
>>>>> the MFD driver and spawn the devices from there. It is confusing
>>>>> if the layout of the driver(s) doesn't really match the layout of the
>>>>> hardware.
>>>>>
>>>>> I understand that it is a pain to write new MFD drivers to get your
>>>>> things going and it would be "nice to get this working really quick
>>>>> now" but in my experience it is better to do it right from the start.
>>>>>
>>>>
>>>> Hi Linus,
>>>>
>>>> Thanks for your advice. I understand the point.
>>>> So, the right modeling would be to:
>>>> - create an MFD driver with the common init part of stmfx
>>>> - remove all common init part of stmfx-pinctrl driver and keep only all
>>>> gpio/pinctrl functions.
>>>>
>>>> I will not develop the other stmfx functions (IDD measurement driver and
>>>> TouchScreen controller driver) because, as explained ealier, they are
>>>> not used on any of the boards using an stmfx and supported by Linux, so
>>>> no way to test these functions, and no need to maintain them while they
>>>> are not being used.
>>>>
>>>> Lee, are you OK with that ?
>>>
>>> I missed a lot of this conversation I think, but from what I've read,
>>> it sounds fine.
>>>
>>
>> I summarize the situation:
>> - I still don't have an official datasheet for STMFX device which could
>> justify the use of an MFD driver;
>> - the MFD driver will contain the STMFX chip initialization stuff such
>> as regmap initialization (regmap structure will be shared with the
>> child), chip initialization, global interrupt management;
>> - there will be only one child (GPIO/PINCTRL node) for the time being.
> 
> But there will be more devices in it. And they will invariably be put
> to use later, and there will be new versions of the chip as well, and
> then you will be happy about doing the MFD core, which makes it
> easy to add new variants with different subdevices.
> 
>> So, is "MFD driver + GPIO/PINCTRL driver" the right modeling, and does
>> it still sound fine after this summary ? :)
> 
> No I think it should use an MFD core.
> 
> Mainly because of device tree concerns.
> 
> The main reason is that the device tree bindings will be different if
> you add an MFD core later, the GPIO and pinctrl driver will
> move to a child node, making old device trees incompatible.
> 
> We could have a single driver in GPIO+pin control if it is a child
> of an MFD node in the device tree, but it doesn't make much
> sense as the I2C device need to be probing to the MFD core.
> 

I agree with you Linus, and that's why all STMFX chip initialization 
stuff was decorrelated in pinctrl-stmfx. This shows that this stuff 
needs to be in an MFD core.

But as there is only one child for now (due to the reasons mentioned 
earlier), it can suggest that it is not a Multi-Function Device.

I'm not able to target when IDD or TS functions will be required on a 
Linux product, but it still makes sense to consider that these functions 
will be used on a Linux product.

So, I think MFD core + GPIO/pinctrl driver is the right modeling, but I 
wanted to be sure that this is okay for everyone. I don't want to spend 
time on something that will not be accepted due to its modeling.

Regards,
Amelie