Re: [PATCH] mmc: tegra: Use sdhci_pltfm_clk_get_max_clock

From: Peter Geis
Date: Tue Jun 05 2018 - 07:58:54 EST




On 06/05/2018 05:28 AM, Thierry Reding wrote:
On Mon, Jun 04, 2018 at 06:35:40PM +0300, Aapo Vienamo wrote:
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.

The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.

Signed-off-by: Aapo Vienamo <avienamo@xxxxxxxxxx>
---
drivers/mmc/host/sdhci-tegra.c | 15 ++-------------
1 file changed, 2 insertions(+), 13 deletions(-)

diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 970d38f6..c8745b5 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -234,17 +234,6 @@ static void tegra_sdhci_set_uhs_signaling(struct sdhci_host *host,
sdhci_set_uhs_signaling(host, timing);
}
-static unsigned int tegra_sdhci_get_max_clock(struct sdhci_host *host)
-{
- struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
-
- /*
- * DDR modes require the host to run at double the card frequency, so
- * the maximum rate we can support is half of the module input clock.
- */
- return clk_round_rate(pltfm_host->clk, UINT_MAX) / 2;
-}

sdhci_pltfm_clk_get_max_clock() returns the current frequency of the
clock, which may not be an accurate maximum.

Also, even if we don't support DDR modes now, we may want to enable them
in the future, at which point we'll need to move to something similar to
the above again, albeit maybe with some of the issues that you mentioned
fixed.

I wonder if we have access to the target mode in this function, because
it seems to me like we'd need to take that into account when determining
the maximum clock rate. Or perhaps the double-rate aspect is already
dealt with in other parts of the MMC subsystem, so the value we should
return here may not even need to take the mode into account.

All of the above said, it is true that we don't enable DDR modes as of
now, and this patch seems like it shouldn't break anything either, so:

Acked-by: Thierry Reding <treding@xxxxxxxxxx>

I also gave this a brief run on Jetson TK1 and things seem to work fine,
so:

Tested-by: Thierry Reding <treding@xxxxxxxxxx>

I am currently testing this in my Ouya project, to see if it makes a difference in my eMMC stability above 30Mhz.
As a drop in replacement it works.
I'll be cranking up the speed later.