Re: [PATCH 2/4] arm: dts: add support for Laird WB50N cpu module and DVK

[Alexandre Belloni]

On 14/06/2018 09:51:55+0100, Ben Whitten wrote:
> Signed-off-by: Ben Whitten <ben.whitten@xxxxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/Makefile        |   3 +-
>  arch/arm/boot/dts/at91-wb50n.dts  | 116 ++++++++++++++++++++++
>  arch/arm/boot/dts/at91-wb50n.dtsi | 202 ++++++++++++++++++++++++++++++++++++++
>  3 files changed, 320 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/at91-wb50n.dts
>  create mode 100644 arch/arm/boot/dts/at91-wb50n.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 1ee94ee..fd5f8a6 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -61,7 +61,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
>  	at91-sama5d4_ma5d4evk.dtb \
>  	at91-sama5d4_xplained.dtb \
>  	at91-sama5d4ek.dtb \
> -	at91-vinco.dtb
> +	at91-vinco.dtb \
> +	at91-wb50n.dtb

I know we have been bad at this but this should be
at91-<soc>-<board>.dtb so at91-sama5d31-wb50n.dtb

>  dtb-$(CONFIG_ARCH_ATLAS6) += \
>  	atlas6-evb.dtb
>  dtb-$(CONFIG_ARCH_ATLAS7) += \
> diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/at91-wb50n.dts
> new file mode 100644
> index 0000000..ee4f823
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-wb50n.dts
> @@ -0,0 +1,116 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * at91-wb50n.dts - Device Tree file for wb50n evaluation board
> + *
> + *  Copyright (C) 2018 Laird
> + *
> + */
> +
> +/dts-v1/;
> +#include "at91-wb50n.dtsi"
> +
> +/ {
> +	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
> +	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +
> +	ahb {
> +		apb {
> +			watchdog@fffffe40 {

I don't mind if you want to have a preparation patch adding the
necessary labels in the soc dtsi so you don't have to reproduce the
ahb/apb hierarchy here.

> +	ahb {
> +		apb {
> +			pinctrl@fffff200 {

Ditto

> +				board {
> +					pinctrl_mmc0_cd: mmc0_cd {
> +						atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */
> +					};
> +
> +					pinctrl_usba_vbus: usba_vbus {
> +						atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&slow_osc {
> +	atmel,osc-bypass;
> +};

After the clock binding rework, this will have to be moved to the pmc
node (the rework is not posted, this is just to remind me that this will
have to be done).

> +
> +&usart1_clk {
> +	atmel,clk-output-range = <0 132000000>;
> +};

The datasheet explicitly states that 66 MHz is the maximum allowed
frequency for the USART. Note that the new binding will not allow you to
do that.

However, I see the table disappeared from the latest datasheet. Maybe
Nicolas can comment on that?

-- 
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com