[PATCH v3 4/6] thermal: tsens: Add support for SDM845

[Amit Kucheria]

SDM845 uses the TSENS v2 IP block

Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
---
 Documentation/devicetree/bindings/thermal/qcom-tsens.txt | 1 +
 arch/arm64/boot/dts/qcom/msm8996.dtsi                    | 2 +-
 drivers/thermal/qcom/tsens-v2.c                          | 9 ++++++++-
 drivers/thermal/qcom/tsens.c                             | 3 +++
 drivers/thermal/qcom/tsens.h                             | 5 ++++-
 5 files changed, 17 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
index 06195e8..84da3db 100644
--- a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
+++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
@@ -5,6 +5,7 @@ Required properties:
  - "qcom,msm8916-tsens" : For 8916 Family of SoCs
  - "qcom,msm8974-tsens" : For 8974 Family of SoCs
  - "qcom,msm8996-tsens" : For 8996 Family of SoCs
+ - "qcom,tsens-v2"      : For any SoC with v2 version of the tsens IP
 
 - reg: Address range of the thermal registers
 - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 6c8a857..28d4c08 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -460,7 +460,7 @@
 		};
 
 		tsens0: thermal-sensor@4a8000 {
-			compatible = "qcom,msm8996-tsens";
+			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
 			#qcom,sensors = <13>;
diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
index c981a40..abc8f13 100644
--- a/drivers/thermal/qcom/tsens-v2.c
+++ b/drivers/thermal/qcom/tsens-v2.c
@@ -69,8 +69,15 @@ static const struct tsens_ops ops_v2 = {
 	.get_temp	= get_temp_tsens_v2,
 };
 
+const struct tsens_data data_tsens_v2 = {
+	.ops            = &ops_v2,
+};
+
+/* Kept around for backward compatibility with old msm8996.dtsi.
+ * New platforms should use data_tsens_v2 if possible and define
+ * the #qcom,sensors property in DT.
+ */
 const struct tsens_data data_8996 = {
 	.num_sensors	= 13,
 	.ops		= &ops_v2,
 };
-
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index 3440166c..a2c9bfa 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -72,6 +72,9 @@ static const struct of_device_id tsens_table[] = {
 	}, {
 		.compatible = "qcom,msm8996-tsens",
 		.data = &data_8996,
+	}, {
+		.compatible = "qcom,tsens-v2",
+		.data = &data_tsens_v2,
 	},
 	{}
 };
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index dc56e1e..69212cb 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -87,6 +87,9 @@ void compute_intercept_slope(struct tsens_device *, u32 *, u32 *, u32);
 int init_common(struct tsens_device *);
 int get_temp_common(struct tsens_device *, int, int *);
 
-extern const struct tsens_data data_8916, data_8974, data_8960, data_8996;
+/* TSENS v1 targets */
+extern const struct tsens_data data_8916, data_8974, data_8960;
+/* TSENS v2 targets */
+extern const struct tsens_data data_8996, data_tsens_v2;
 
 #endif /* __QCOM_TSENS_H__ */
-- 
2.7.4