RE: [PATCH V2 1/3] scsi: ufs: set the device reference clock setting

[sayali]

Comment inline.

Thanks,
Sayali
-----Original Message-----
From: Rob Herring [mailto:robh@xxxxxxxxxx] 
Sent: Wednesday, June 13, 2018 12:57 AM
To: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>
Cc: subhashj@xxxxxxxxxxxxxx; cang@xxxxxxxxxxxxxx;
vivek.gautam@xxxxxxxxxxxxxx; rnayak@xxxxxxxxxxxxxx; vinholikatti@xxxxxxxxx;
jejb@xxxxxxxxxxxxxxxxxx; martin.petersen@xxxxxxxxxx;
asutoshd@xxxxxxxxxxxxxx; evgreen@xxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx;
Mark Rutland <mark.rutland@xxxxxxx>; Mathieu Malaterre <malat@xxxxxxxxxx>;
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
<devicetree@xxxxxxxxxxxxxxx>; open list <linux-kernel@xxxxxxxxxxxxxxx>
Subject: Re: [PATCH V2 1/3] scsi: ufs: set the device reference clock
setting

On Fri, Jun 08, 2018 at 04:36:28PM +0530, Sayali Lokhande wrote:
> From: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx>
> 
> UFS host supplies the reference clock to UFS device and UFS device 
> specification allows host to provide one of the 4 frequencies (19.2 
> MHz,
> 26 MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the 
> device reference clock frequency setting in the device based on what 
> frequency it is supplying to UFS device.
> 
> Signed-off-by: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx>
> Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
> Signed-off-by: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/ufs/ufshcd-pltfrm.txt      |  7 +++
>  drivers/scsi/ufs/ufs.h                             |  9 ++++
>  drivers/scsi/ufs/ufshcd-pltfrm.c                   | 24 ++++++++++
>  drivers/scsi/ufs/ufshcd.c                          | 52
++++++++++++++++++++++
>  drivers/scsi/ufs/ufshcd.h                          |  1 +
>  5 files changed, 93 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt 
> b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> index c39dfef..4522434 100644
> --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> @@ -41,6 +41,12 @@ Optional properties:
>  -lanes-per-direction	: number of lanes available per direction - either 1
or 2.
>  			  Note that it is assume same number of lanes is
used both
>  			  directions at once. If not specified, default is 2
lanes per direction.
> +- dev-ref-clk-freq	: Specify the device reference clock frequency, must
be one of the following:
> +			  0: 19.2 MHz
> +			  1: 26 MHz
> +			  2: 38.4 MHz
> +			  3: 52 MHz
> +			  Defaults to 26 MHz if not specified.

I must have misunderstood your last response. I thought you could handle
things without DT. If not, my question remains.
[Sayali]: Ref clk frequency setting could vary from
platfrom-to-platform(vendor specific). Hence we need to pass it via DT.
	Currently in DT we do not set/mention any ref clk frequency
parameter. Hence I have added one new DT entry to configure
	required ref clk freq.

Rob