[PATCH v6 8/8] Documentation/ABI: Add documentation mlxreg-io sysfs interfaces

[Vadim Pasternak]

Add documentation for mlxreg-io platform driver sysfs interfaces to allow
user space access for system resets control, reset causes monitoring,
programmable devices version reading and device selection control.

Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
---
v5-v6:
 Changes added by Vadim:
 - Change kernel version from 4.18 to 4.19.
v4-v5:
 Comments pointed out by Darren:
 - Rename cause to reset.
 - Extend explanation in doc file.
 Changes added by Vadim:
 - Add two new attributes.
 - Re-arrange in alphabetic order after changes.
 - Change date from May to June.
v4:
 Comments pointed out by Greg:
 Add Documentation/ABI/ entries for the new sysfs files.
---
 Documentation/ABI/stable/sysfs-driver-mlxreg-io | 77 +++++++++++++++++++++++++
 1 file changed, 77 insertions(+)
 create mode 100644 Documentation/ABI/stable/sysfs-driver-mlxreg-io

diff --git a/Documentation/ABI/stable/sysfs-driver-mlxreg-io b/Documentation/ABI/stable/sysfs-driver-mlxreg-io
new file mode 100644
index 0000000..815689b
--- /dev/null
+++ b/Documentation/ABI/stable/sysfs-driver-mlxreg-io
@@ -0,0 +1,77 @@
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+							asic_health
+
+Date:		June 2018
+KernelVersion:	4.19
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	This file shows ASIC health status. The possible values are:
+		0 - health failed, 2 - health OK, 3 - ASIC in booting state.
+
+		The files are read only.
+
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+							cpld1_version
+							cpld2_version
+
+Date:		June 2018
+KernelVersion:	4.19
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	These files show with which CPLD versions have been burned
+		on carrier and switch boards.
+
+		The files are read only.
+
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/select_iio
+Date:		June 2018
+KernelVersion:	4.19
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	This file allows iio devices selection.
+
+		Attribute select_iio can be written with 0 or with 1. It
+		selects which one of iio devices can be accessed.
+
+		The file is read/write.
+
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu1_on
+		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu2_on
+		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_cycle
+		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_down
+Date:		June 2018
+KernelVersion:	4.19
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	These files allow asserting system power cycling, switching
+		power supply units on and off and system's main power domain
+		shutdown.
+		Expected behavior:
+		When pwr_cycle is written 1: auxiliary power domain will go
+		down and after short period (about 1 second) up.
+		When  psu1_on or psu2_on is written 1, related unit will be
+		disconnected from the power source, when written 0 - connected.
+		If both are written 1 - power supplies main power domain will
+		go down.
+		When pwr_down is written 1, system's main power domain will go
+		down.
+
+		The files are write only.
+
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+							reset_aux_pwr_or_ref
+							reset_asic_thermal
+							reset_hotswap_or_wd
+							reset_fw_reset
+							reset_long_pb
+							reset_main_pwr_fail
+							reset_short_pb
+							reset_sw_reset
+Date:		June 2018
+KernelVersion:	4.19
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	These files show the system reset cause, as following: power
+		auxiliary outage or power refresh, ASIC thermal shutdown,
+		hotswap or watchdog, firmware reset, long press power button,
+		short press power button, software reset. Value 1 in file means
+		this is reset cause, 0 - otherwise. Only one of the above
+		causes could be 1 at the same time, representing only last
+		reset cause.
+
+		The files are read only.
-- 
2.1.4