Re: [PATCH v6 0/6] mtd: rawnand: support MT29F1G08ABAFAWP-ITE:F

[Miquel Raynal]

Hi Chris,

On Mon, 25 Jun 2018 10:44:42 +1200, Chris Packham
<chris.packham@xxxxxxxxxxxxxxxxxxx> wrote:

> Hi,
> 
> I'm looking at adding support for the Micron MT29F1G08ABAFAWP-ITE:F chip
> to one of our boards which uses the Marvell NFCv2 controller.
> 
> This particular chip is a bit odd in that the datasheet states support
> for ONFI 1.0 but the revision number field is 00 00. It also is marked
> ABAFA but reports internally as ABAGA. Finally it has internal 8-bit ECC
> which cannot be disabled.
> 
> The existing test in micron_supports_on_die_ecc() determines that on-die
> ECC is supported but not mandatory but I know for this chip it is
> mandatory despite what set_features returns.
> 
> In order for this to work I need to set nand-ecc-mode = "on-die" in my
> dts. Ideally I'd like it to be automatic based on what the hardware can
> support but that may be asking too much at the moment.
> 
> Here's a dump of the parameter page from the chip I have
> 
> 00000000: 4f 4e 46 49 00 00 18 00 3f 00 00 00 00 00 00 00 ONFI....?.......
> 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 00000020: 4d 49 43 52 4f 4e 20 20 20 20 20 20 4d 54 32 39  MICRON MT29
> 00000030: 46 31 47 30 38 41 42 41 47 41 57 50 20 20 20 20  F1G08ABAGAWP    
> 00000040: 2c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ,...............
> 00000050: 00 08 00 00 80 00 00 02 00 00 20 00 40 00 00 00  ..........  .@...
> 00000060: 00 04 00 00 01 22 01 14 00 01 05 08 00 00 04 00 ....."..........
> 00000070: 08 01 0e 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 00000080: 08 3f 00 3f 00 58 02 10 27 46 00 64 00 00 00 00 .?.?.X..'F.d....
> 00000090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 000000a0: 00 00 00 00 01 00 00 00 00 02 04 80 01 81 04 03 ................
> 000000b0: 02 01 1e 90 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 000000d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 000000e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 000000f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 85 a6 ................
> 
> Series changes in v3:
> - No longer RFC
> - dropped "mtd: rawnand: micron: add ONFI_FEATURE_ON_DIE_ECC to supported
>   features" which Boris has already picked up
> - dropped "mtd: rawnand: marvell: Support page size of 2048 with 8-bit ECC"
>   since I can't test it.
> 
> Series changes in v4:
> - based on top of http://patchwork.ozlabs.org/patch/932006/
> 
> Series changes in v5:
> - address review comments from Boris on patches 5 and 6
> 
> Series changes in v6:
> - Update commit message on 6/6
> 
> Chris Packham (6):
>   mtd: rawnand: marvell: Handle on-die ECC
>   mtd: rawnand: add manufacturer fixup for ONFI parameter page
>   mtd: rawnand: add defines for ONFI version bits
>   mtd: rawnand: micron: add fixup for ONFI revision
>   mtd: rawnand: micron: support 8/512 on-die ECC
>   mtd: rawnand: micron: detect forced on-die ECC
> 
>  drivers/mtd/nand/raw/marvell_nand.c |   1 +
>  drivers/mtd/nand/raw/nand_base.c    |  14 +--
>  drivers/mtd/nand/raw/nand_micron.c  | 129 +++++++++++++++++++++++-----
>  include/linux/mtd/rawnand.h         |  14 +++
>  4 files changed, 131 insertions(+), 27 deletions(-)
> 

Applied to nand/next, I just changed the way you aligned/not aligned
some lines to respect the 80 columns rule.

Thanks,
MiquÃl